Subject	Stock, I am setting the record for the most overbuilt stock
Posted by	Chip(GinnMotorsports) on December 13, 2002 at 3:38 PM
	This message has been viewed 61 times.
In Reply To	Looks good. :) What Fuel pump are you using? (n/m) posted by DamonH 90TT on December 13, 2002 at 02:47 PM
Message	turbo setup. FMIC with 2.25"/2.5" piping, 850cc injectors, etc. I am tired of waiting for the manifolds. It is going back together as is so that I can drive it. 9 months is too long to wait.
Follow Ups	Pics of parallel feed Border 850cc fuel system - Chip(GinnMotorsports) 14:32:11 12/13/02 How easy does it install? Any shaving of the plenum? (n/m) - AshsZ (King of FAB) 14:36:16 12/13/02 Wagz has it.. said fit pretty nicely. No shaving needed. (n/m) - Milo (San Antonio, TX.) 15:07:20 12/13/02 Thanks Chip. ;-) (n/m) - AshsZ (King of FAB) 15:12:07 12/13/02 new SN Chip? (n/m) - sbsTT(MD) 15:17:42 12/13/02 Anytime. (n/m) - Milo (San Antonio, TX.) 15:39:10 12/13/02 is that a yes or a no? (n/m) - sbsTT(MD) 15:52:24 12/13/02 In McEnroe voice: "You can't be serious!" (n/m) - Chip(GinnMotorsports) 15:58:48 12/13/02 lmao - sbsTT(MD) 16:45:29 12/13/02 mine isnt installed fully yet-supposed to be done tuesday - Wagz 16:58:00 12/13/02 After looking today, there is one spot that I am concerned - Chip(GinnMotorsports) 15:41:34 12/13/02 Just wondering.... - Mal1ce 14:38:06 12/13/02 Isn't that how it's set up in the pics? (n/m) - dragonballz 14:48:09 12/13/02 *sigh* Im not really awake today....thx. (n/m) - Mal1ce 15:07:30 12/13/02 Yes, but hard to tell with my rigged setup - Chip(GinnMotorsports) 15:36:12 12/13/02 Nice, I am intrested, what fuel lines are you running to - dragonballz 14:45:43 12/13/02 When I put the plenum back on >> - Chip(GinnMotorsports) 15:35:01 12/13/02 Looks good. :) What Fuel pump are you using? (n/m) - DamonH 90TT 14:47:23 12/13/02 Stock, I am setting the record for the most overbuilt stock - Chip(GinnMotorsports) 15:38:18 12/13/02 is that what your guy said? I thought it was faster? (n/m) - Carlos Ramirez 17:32:55 12/13/02 The problem is that I ordered 2 sets and they are sold - Chip(GinnMotorsports) 17:49:33 12/13/02 Chip, are the lines w/the 90degree - thebigtman (San Antonio, TX) 15:12:20 12/13/02 Yes those are the ones that I am replacing - Chip(GinnMotorsports) 15:32:20 12/13/02 very nice! (n/m) - sbsTT(MD) 15:15:04 12/13/02 Very nice looks almost like my setup. The return - MikeH(Twin GT35BB Incon Z) 16:41:40 12/13/02 I could not get my bends anywhere near as sharp as yours - Chip(GinnMotorsports) 16:48:04 12/13/02 I had Grandberry supplies make my hard steel lines (n/m) - MikeH(Twin GT35BB Incon Z) 17:39:06 12/13/02 Clean up those wires in the back! (n/m) - Mike (La Canada) 16:42:41 12/13/02 It is nowhere near being ready to run, - Chip(GinnMotorsports) 16:46:27 12/13/02 just messin with ya (n/m) - Mike (La Canada) 18:49:53 12/13/02 great pics bro-any advice 4 me? mine R supposed to go in - Wagz 17:00:53 12/13/02 My advise is DO NOT pay someone to do what I did - Chip(GinnMotorsports) 17:29:58 12/13/02 ya-i'm basically doing the normal instal but w/> - Wagz 17:38:17 12/13/02 If the rail touches the plenum I would guess that they - Chip(GinnMotorsports) 17:47:10 12/13/02 You should know already what to do with your GF or Wife :) (n/m) - MikeH(Twin GT35BB Incon Z) 17:47:12 12/13/02 Have SGP do it , they'll charge you just for parts only :) (n/m) - MikeH(Twin GT35BB Incon Z) 17:43:53 12/13/02 Yeah but now that you have done it once I am sure you---> - Kyle(Houston) 13:02:58 12/14/02 Looks good Chip....what size feed line will you be using?... (n/m) - Kyle(Houston) 17:16:59 12/13/02 -6 right now, -8 when I upgrade the pump - Chip(GinnMotorsports) 17:28:05 12/13/02 LOL....gotcha...I was going to say that a -6 T'ed into---> - Kyle(Houston) 17:48:30 12/13/02 There is actually another way you may not have considered... - B-Ster 17:31:22 12/13/02 The front lines looks almost kinked? (n/m) - MikeH(Twin GT35BB Incon Z) 13:09:53 12/14/02
Post a Followup	You cannot reply to this message because you are not logged in.