Subject	Pics of parallel feed Border 850cc fuel system
Posted by	Chip(GinnMotorsports) on December 13, 2002 at 2:32 PM
	This message has been viewed 544 times.
Message	Ignore long rubber hoses running to/from hard lines, this was temporary to pressure test my fittings. I am redoing the lines below. The center outlet needs to be in line with the junction of the 2 cam sprocket covers. There is enough room to run the outlet line under the front of the upper plenum and above the sprocket covers. The inlet lines were and and testfit process. This is the tightest area of the plumbing. I pushed the metal waterline back ~.25". The rubber line was rubbing the plenum, so it needed to be bent anyway.
Follow Ups	Pics of parallel feed Border 850cc fuel system - Chip(GinnMotorsports) 14:32:11 12/13/02 How easy does it install? Any shaving of the plenum? (n/m) - AshsZ (King of FAB) 14:36:16 12/13/02 Wagz has it.. said fit pretty nicely. No shaving needed. (n/m) - Milo (San Antonio, TX.) 15:07:20 12/13/02 Thanks Chip. ;-) (n/m) - AshsZ (King of FAB) 15:12:07 12/13/02 new SN Chip? (n/m) - sbsTT(MD) 15:17:42 12/13/02 Anytime. (n/m) - Milo (San Antonio, TX.) 15:39:10 12/13/02 is that a yes or a no? (n/m) - sbsTT(MD) 15:52:24 12/13/02 In McEnroe voice: "You can't be serious!" (n/m) - Chip(GinnMotorsports) 15:58:48 12/13/02 lmao - sbsTT(MD) 16:45:29 12/13/02 mine isnt installed fully yet-supposed to be done tuesday - Wagz 16:58:00 12/13/02 After looking today, there is one spot that I am concerned - Chip(GinnMotorsports) 15:41:34 12/13/02 Just wondering.... - Mal1ce 14:38:06 12/13/02 Isn't that how it's set up in the pics? (n/m) - dragonballz 14:48:09 12/13/02 *sigh* Im not really awake today....thx. (n/m) - Mal1ce 15:07:30 12/13/02 Yes, but hard to tell with my rigged setup - Chip(GinnMotorsports) 15:36:12 12/13/02 Nice, I am intrested, what fuel lines are you running to - dragonballz 14:45:43 12/13/02 When I put the plenum back on >> - Chip(GinnMotorsports) 15:35:01 12/13/02 Looks good. :) What Fuel pump are you using? (n/m) - DamonH 90TT 14:47:23 12/13/02 Stock, I am setting the record for the most overbuilt stock - Chip(GinnMotorsports) 15:38:18 12/13/02 is that what your guy said? I thought it was faster? (n/m) - Carlos Ramirez 17:32:55 12/13/02 The problem is that I ordered 2 sets and they are sold - Chip(GinnMotorsports) 17:49:33 12/13/02 Chip, are the lines w/the 90degree - thebigtman (San Antonio, TX) 15:12:20 12/13/02 Yes those are the ones that I am replacing - Chip(GinnMotorsports) 15:32:20 12/13/02 very nice! (n/m) - sbsTT(MD) 15:15:04 12/13/02 Very nice looks almost like my setup. The return - MikeH(Twin GT35BB Incon Z) 16:41:40 12/13/02 I could not get my bends anywhere near as sharp as yours - Chip(GinnMotorsports) 16:48:04 12/13/02 I had Grandberry supplies make my hard steel lines (n/m) - MikeH(Twin GT35BB Incon Z) 17:39:06 12/13/02 Clean up those wires in the back! (n/m) - Mike (La Canada) 16:42:41 12/13/02 It is nowhere near being ready to run, - Chip(GinnMotorsports) 16:46:27 12/13/02 just messin with ya (n/m) - Mike (La Canada) 18:49:53 12/13/02 great pics bro-any advice 4 me? mine R supposed to go in - Wagz 17:00:53 12/13/02 My advise is DO NOT pay someone to do what I did - Chip(GinnMotorsports) 17:29:58 12/13/02 ya-i'm basically doing the normal instal but w/> - Wagz 17:38:17 12/13/02 If the rail touches the plenum I would guess that they - Chip(GinnMotorsports) 17:47:10 12/13/02 You should know already what to do with your GF or Wife :) (n/m) - MikeH(Twin GT35BB Incon Z) 17:47:12 12/13/02 Have SGP do it , they'll charge you just for parts only :) (n/m) - MikeH(Twin GT35BB Incon Z) 17:43:53 12/13/02 Yeah but now that you have done it once I am sure you---> - Kyle(Houston) 13:02:58 12/14/02 Looks good Chip....what size feed line will you be using?... (n/m) - Kyle(Houston) 17:16:59 12/13/02 -6 right now, -8 when I upgrade the pump - Chip(GinnMotorsports) 17:28:05 12/13/02 LOL....gotcha...I was going to say that a -6 T'ed into---> - Kyle(Houston) 17:48:30 12/13/02 There is actually another way you may not have considered... - B-Ster 17:31:22 12/13/02 The front lines looks almost kinked? (n/m) - MikeH(Twin GT35BB Incon Z) 13:09:53 12/14/02
Post a Followup	You cannot reply to this message because you are not logged in.