Subject	if its rod a bearing going bad...
Posted by	aliaZ on October 09, 2002 at 10:51 PM
	This message has been viewed 206 times.
In Reply To	whats the symptoms of a spun bearing? posted by nixit(da][as) on October 09, 2002 at 03:14 PM
Message	the noise will go away when you pull your coil pack connection on the offending cylinder. For what its worth, my grandpa's station wagon spun a bearing, but I was able to drive it home 120 miles after pulling the corresponding plug wire. Honestly, I don't think it is a rod bearing you are hearing, otherwise I don't think you would have been able to get this far
Follow Ups	whats the symptoms of a spun bearing? - nixit(da][as) 15:14:57 10/09/02 retighten your pass side down pipes again? (n/m) - Halo Z 15:21:26 10/09/02 oh yeah "symptoms": low oil pressure is one. (n/m) - Halo Z 15:22:17 10/09/02 pressure is dead on. normal. no smell of oil or gas in fluid - nixit(da][as) 15:23:32 10/09/02 pull coil packs, one by one, see if it's verys per cyl. (n/m) - Halo Z 15:26:08 10/09/02 good idea. I was thinking "wrist pin" with this diagnosis. - nixit(da][as) 15:37:05 10/09/02 might just be the turbo it's self. time to upgrade (n/m) - Halo Z 15:39:47 10/09/02 Time for TD-05's! (n/m) - Kenny (9 psi TT + NA) 15:41:03 10/09/02 nope. JWT 500s. unless they make a TD-01. - nixit(da][as) 15:46:36 10/09/02 people that blame the president for our problems - joel(PA) 16:34:47 10/09/02 don't start. (n/m) - Halo Z 16:52:17 10/09/02 sorry =P (n/m) - joel(PA) 17:10:58 10/09/02 Remember that night at the zcon? boy, i was a scared - nixit(da][as) 15:52:45 10/09/02 now you got me thinkering... - nixit(da][as) 16:03:31 10/09/02 so you have had this noise for over 1k? - Halo Z 16:23:12 10/09/02 possible cracked rod cap??? (n/m) - SacTown-TTZ 16:25:20 10/09/02 yea. not necessarily the same noise this time. (n/m) - nixit(da][as) 15:22:21 10/09/02 Online info>>>> - Kenny (9 psi TT + NA) 15:25:54 10/09/02 Thanks Kenny - nixit(da][as) 15:36:17 10/09/02 No prob. =) - Kenny (9 psi TT + NA) 15:40:01 10/09/02 we are still prototyping everything... - nixit(da][as) 15:58:00 10/09/02 David? he okay? (n/m) - Guapo 16:55:16 10/09/02 Sounds like it could be a rod knock... - SacTown-TTZ 15:46:10 10/09/02 Agreed, sounds very much like it could be a rod knock...>>> - 5150Z 11:06:34 10/10/02 spun rod bearing almost always lowers oil psi - AntiHero[seatbelts rock] 17:08:57 10/09/02 Sweet. not a spun rod bearing then. - nixit(da][as) 18:00:13 10/09/02 I ran mine like that nearly a year at stage III. :) - DamonH 90TT 17:59:15 10/09/02 if its rod a bearing going bad... - aliaZ 22:51:46 10/09/02 When I spun my #1 rod bearing it was just a clunk>> - dilly yo 04:56:53 10/10/02
Post a Followup	You cannot reply to this message because you are not logged in.