Subject	Re: You most likely said, but did you replace the
Posted by	acetrebo on September 02, 2025 at 8:18 AM
	This message has been viewed 6 times.
In Reply To	You most likely said, but did you replace the posted by Denis on August 31, 2025 at 11:59 PM
Message	Yes, a new throw out bearing came with the clutch kit, so I did install a new one. It doesn't look any different than the stock one, but it was installed. Thanks!
Follow Ups	Need clutch help - acetrebo 14:27:05 08/26/25 Re: Need clutch help - acetrebo 16:07:59 08/26/25 Re: Need clutch help - acetrebo 17:08:33 08/26/25 Re: Re: Need clutch help - itsa300zx 17:38:49 08/26/25 Re: Re: Re: Need clutch help - acetrebo 18:01:59 08/26/25 Re: Re: Re: Re: Need clutch help - acetrebo 22:23:31 08/26/25 Likely installed clutch disc in backwards - However, check - Ghoztt (MD) 10:56:58 08/27/25 Agreed, I think it would be best to pull the trans again - Polishzx 16:46:35 08/27/25 Re: Agreed, I think it would be best to pull the trans again - acetrebo 23:58:01 08/27/25 The stock ones can flex but I don't think enough to not get - Polishzx 00:49:06 08/28/25 Re: The stock ones can flex but I don't think enough to not get - acetrebo 08:05:51 08/28/25 Re: Re: The stock ones can flex but I don't think enough to not get - acetrebo 08:16:33 08/28/25 Re: Likely installed clutch disc in backwards - However, check - acetrebo 23:54:21 08/27/25 Sadly, it can and has been done. - Ghoztt (MD) 14:08:08 08/28/25 Re: Sadly, it can and has been done. - acetrebo 18:34:37 08/28/25 Re: Likely installed clutch disc in backwards - However, check - acetrebo 00:00:07 08/28/25 Where are you in the "USA" ? One of the Z community - Denis 11:08:56 08/28/25 Re: Where are you in the "USA" ? One of the Z community - acetrebo 18:36:55 08/28/25 I may have my head on backward on this but - Denis 11:51:33 08/28/25 The bottoming out sounds like physical interference inside - Ghoztt (MD) 14:16:48 08/28/25 Re: The bottoming out sounds like physical interference inside - acetrebo 18:43:22 08/28/25 The bottoming out term I used - Denis 20:41:15 08/28/25 Re: The bottoming out term I used - acetrebo 22:22:06 08/28/25 Re: I may have my head on backward on this but - acetrebo 18:41:01 08/28/25 Re: Re: I may have my head on backward on this but - Denis 20:56:53 08/28/25 Re: Re: Re: I may have my head on backward on this but - acetrebo 22:13:40 08/28/25 OK, disregard my earlier suggestions - Denis 22:41:11 08/28/25 Re: OK, disregard my earlier suggestions - acetrebo 22:49:37 08/28/25 Re: OK, disregard my earlier suggestions - acetrebo 22:53:34 08/28/25 Sometimes it is possible to dig - Denis 13:21:13 08/29/25 Make that ding (n/m) - Denis 13:24:01 08/29/25 Re: Sometimes it is possible to dig - acetrebo 13:47:41 08/29/25 Good Luck! (n/m) - Denis 16:43:25 08/29/25 Re: Good Luck! - acetrebo 21:32:04 08/31/25 You most likely said, but did you replace the - Denis 23:59:07 08/31/25 Re: You most likely said, but did you replace the - acetrebo 08:18:16 09/02/25 Re: Need clutch help - mrchips 06:18:21 08/31/25 Re: Re: Need clutch help - acetrebo 08:21:28 09/02/25
Post a Followup	You cannot reply to this message because you are not logged in.