Subject	Re: Re: Re: I may have my head on backward on this but
Posted by	acetrebo on August 28, 2025 at 10:13 PM
	This message has been viewed 11 times.
In Reply To	Re: Re: I may have my head on backward on this but posted by Denis on August 28, 2025 at 08:56 PM
Message	So, I have not driven the car yet. Its still on jackstands, all put together. If car is off, I can shift through gears smoothly. If I start the car in Nuetral, I am unable to get the car into gear with the clutch pushed in. If I force it into 1st, which I can, the wheels spin, and if I then push the clutch in all the way, the wheels are still spinning. so the clutch plate is not disengaging. I did not drop the car until I was sure everything was going to work properly. Im kind of stumped. All the parts are new (except the slave and master that are on the way.) New flywheel, new clutch, new throwout bearing, fork looked fine, everything moved as it should before I re-installed the tranny. Fork still moves when pedal depressed although I think not far enough. Not sure. Never paid close attention on how far the fork moved until now. So hoping the new master fixes the issue. If not I'll remove and try to see what the heck is happening lol. Maybe the fork is flexing. Thats what z1 said could be the issue.
Follow Ups	Need clutch help - acetrebo 14:27:05 08/26/25 Re: Need clutch help - acetrebo 16:07:59 08/26/25 Re: Need clutch help - acetrebo 17:08:33 08/26/25 Re: Re: Need clutch help - itsa300zx 17:38:49 08/26/25 Re: Re: Re: Need clutch help - acetrebo 18:01:59 08/26/25 Re: Re: Re: Re: Need clutch help - acetrebo 22:23:31 08/26/25 Likely installed clutch disc in backwards - However, check - Ghoztt (MD) 10:56:58 08/27/25 Agreed, I think it would be best to pull the trans again - Polishzx 16:46:35 08/27/25 Re: Agreed, I think it would be best to pull the trans again - acetrebo 23:58:01 08/27/25 The stock ones can flex but I don't think enough to not get - Polishzx 00:49:06 08/28/25 Re: The stock ones can flex but I don't think enough to not get - acetrebo 08:05:51 08/28/25 Re: Re: The stock ones can flex but I don't think enough to not get - acetrebo 08:16:33 08/28/25 Re: Likely installed clutch disc in backwards - However, check - acetrebo 23:54:21 08/27/25 Sadly, it can and has been done. - Ghoztt (MD) 14:08:08 08/28/25 Re: Sadly, it can and has been done. - acetrebo 18:34:37 08/28/25 Re: Likely installed clutch disc in backwards - However, check - acetrebo 00:00:07 08/28/25 Where are you in the "USA" ? One of the Z community - Denis 11:08:56 08/28/25 Re: Where are you in the "USA" ? One of the Z community - acetrebo 18:36:55 08/28/25 I may have my head on backward on this but - Denis 11:51:33 08/28/25 The bottoming out sounds like physical interference inside - Ghoztt (MD) 14:16:48 08/28/25 Re: The bottoming out sounds like physical interference inside - acetrebo 18:43:22 08/28/25 The bottoming out term I used - Denis 20:41:15 08/28/25 Re: The bottoming out term I used - acetrebo 22:22:06 08/28/25 Re: I may have my head on backward on this but - acetrebo 18:41:01 08/28/25 Re: Re: I may have my head on backward on this but - Denis 20:56:53 08/28/25 Re: Re: Re: I may have my head on backward on this but - acetrebo 22:13:40 08/28/25 OK, disregard my earlier suggestions - Denis 22:41:11 08/28/25 Re: OK, disregard my earlier suggestions - acetrebo 22:49:37 08/28/25 Re: OK, disregard my earlier suggestions - acetrebo 22:53:34 08/28/25 Sometimes it is possible to dig - Denis 13:21:13 08/29/25 Make that ding (n/m) - Denis 13:24:01 08/29/25 Re: Sometimes it is possible to dig - acetrebo 13:47:41 08/29/25 Good Luck! (n/m) - Denis 16:43:25 08/29/25 Re: Good Luck! - acetrebo 21:32:04 08/31/25 You most likely said, but did you replace the - Denis 23:59:07 08/31/25 Re: Need clutch help - mrchips 06:18:21 08/31/25
Post a Followup	You cannot reply to this message because you are not logged in.