Subject	I checked for fluid at the firewall today.
Posted by	rojoloco (VA Beach) on May 03, 2012 at 8:18 PM
	This message has been viewed 187 times.
In Reply To	Not sure. I had times where I could shift like butter posted by doug8867 on May 03, 2012 at 02:40 PM
Message	There was nothing up by the pedal. It was dry as a bone which would correlate to my fluid level not dropping at all. There is definitely a lot of wetness down by the slave but I think it is coming from one of the oil lines (had to reuse some during the build) above because it is pretty nasty up there right now. I'm guessing a complete lack of fluid by the pedal would mean the master cylinder is good right? I just noticed the boot was a tad ripped and that was all. Underneath, the slave cylinder is definitely moving as the pedal is depressed. I can see it moving the clutch fork. It just feels very squishy as a whole. I might try the pedal adjustment tomorrow just to see if I can get it to work until I can figure out the actual problem. ----------------------------------------------------- Never Play Leapfrog With A Unicorn!!! Do yourself a favor and just worry about your own car. I don't see what everyone is so worried about anyway. If someone else wants to perform a modification that you believe will destroy the value, cheapen the Z32 or whatever you can't sit on your hands about, wouldn't that make your tastefully-modified, white bread Z32 more rare and valuable? -- BradZ (FL) on December 23, 2007 at 12:19 PM The unicorn gets its revenge... -- Scotts94z32 on September 19, 2006 at 11:12 AM CLICK FOR DETAILS ABOUT BUYING A ZAMA POSTER!!!!
Follow Ups	Clutch bleed fail - rojoloco (VA Beach) 14:49:09 04/29/12 Maybe the seal on the MC is shot and letting air in? - my91z 15:05:59 04/29/12 No leakage at all. - rojoloco (VA Beach) 15:23:23 04/29/12 One of the bleeders not holding tight and sucking air >> - my91z 15:37:49 04/29/12 I've had this bleeders problem too - OverZealous (CT) 16:27:41 04/29/12 Do you have a write-up? (n/m) - rojoloco (VA Beach) 18:49:21 04/29/12 Not a lot to it - install SB into the slave cylinder, - jzack 22:29:11 04/29/12 Gotcha. I've never used a SB. - rojoloco (VA Beach) 05:29:24 04/30/12 Cheap Siphon Reverse Bleed Setup - OverZealous (CT) 22:16:38 04/30/12 Thanks! I'll have to try this method. - rojoloco (VA Beach) 09:56:09 05/01/12 Did you get my email? (n/m) - my91z 16:16:45 05/01/12 If it was sent today, not yet. I replied to one this morning - rojoloco (VA Beach) 13:43:51 05/02/12 I've gotten good results using a speedbleeders bleeder (n/m) - AHos(Chicago) 18:54:45 04/29/12 If you can't even shift the car into gear there would - doug8867 21:00:03 05/01/12 I've gotten conflicting info on the clutch booster. - rojoloco (VA Beach) 13:47:00 05/02/12 Agree that booster is not likely to cause your - doug8867 15:13:54 05/02/12 I can try it. - rojoloco (VA Beach) 05:56:39 05/03/12 You had me at: - doug8867 08:20:34 05/03/12 That still leaves a few unanswered questions though. - rojoloco (VA Beach) 11:52:34 05/03/12 Not sure. I had times where I could shift like butter - doug8867 14:40:06 05/03/12 I checked for fluid at the firewall today. - rojoloco (VA Beach) 20:18:49 05/03/12 I would thoroughly clean you slave of wetness, then - doug8867 07:03:45 05/04/12 The slave better not be dead. - rojoloco (VA Beach) 09:11:13 05/04/12 Still trying to picture how a LOT of oil could work itself - doug8867 10:20:23 05/04/12 Now you can fully understand my confusion. - rojoloco (VA Beach) 10:33:13 05/04/12 The pedal adjustment didn't do squat. - rojoloco (VA Beach) 22:18:35 05/04/12 Did you clean your slave first and then inspect - doug8867 09:44:12 05/07/12 Yeah, I cleaned it first. - rojoloco (VA Beach) 08:32:05 05/09/12 Forgot to answer your question about rebuilding MC. - doug8867 11:44:13 05/03/12
Post a Followup	You cannot reply to this message because you are not logged in.