Subject	Thanks for all the suggestions...Dwayne
Posted by	dwayne on April 23, 2010 at 12:13 PM
	This message has been viewed 358 times.
In Reply To	Re: Driveshaft Issues after Z1 1-piece install on a 93 Z 2+2 posted by bryan@Z1 on April 23, 2010 at 11:38 AM
Message	I understand that this is very rare occurrence of out of balance. The driveshaft shop did find it out of balance. They balanced it as mentioned and still issues at higher speeds. I was really hoping this 1 piece would be the ticket as I read a lot of great reviews on it. I know many coupe folks are happy with it...I don't know however if there are many 2+2s with the 1-piece. I will contact Z1 on next steps. I would want to mention that I have ordered many parts from Z1 over the years and never had a problem and the staff has always been responsive. Will keep you posted on the next steps. Thanks again everyone for the suggestions and advice. This board has always been helpful.
Follow Ups	Driveshaft Issues after Z1 1-piece install on a 93 Z 2+2 - dwayne 23:26:01 04/22/10 #3 - ZLover4Life 23:33:00 04/22/10 My assumption is that it was due to u-joint operating angles - Ashman2k2 21:13:27 04/27/10 #3 - Draker (Eugene, OR) 23:41:37 04/22/10 #3 ... Had you "searched" and read up on one-piece - zellamay 00:51:26 04/23/10 I have talked to many Z'ers with the one peice Z1 Platinum - KongZTT GT28RS MD 01:10:36 04/23/10 Why? Is it that feeling of relief when you get it - zellamay 13:51:28 04/23/10 There is a procedure to properly install the driveshaft - KongZTT GT28RS MD 01:13:49 04/23/10 it involves measuring the runout, and I believe it only - LJZTT 05:08:31 04/23/10 There are manufacturing tolerances in every part. - zellamay 13:39:45 04/23/10 hmmm, so you're saying the vibration is the result of the - LJZTT 20:17:03 04/23/10 send it back for another, its obviously flawed (n/m) - Z32TT-R 03:25:19 04/23/10 EXACT same issue here, although mine is with an EPRacing - LJZTT 04:57:57 04/23/10 Re: EXACT same issue here, although mine is with an EPRacing - Tech@EPR 05:51:49 04/23/10 I understand the differences. I must not have received bolts - LJZTT 07:49:49 04/23/10 Re: I understand the differences. I must not have received bolts - Tech@EPR 09:33:35 04/23/10 Re: Driveshaft Issues after Z1 1-piece install on a 93 Z 2+2 - ak420 07:02:10 04/23/10 how would you describe the shudder? - ZiNnYc 07:05:01 04/23/10 I had problems with a 1-Piece, and went back - Trailboss 07:08:19 04/23/10 this install requires only about 3 different - KasbeKZ(VA) 07:21:12 04/23/10 If you have a worn out transmission mount or - RICH1 08:11:59 04/23/10 Re: Driveshaft Issues after Z1 1-piece install on a 93 Z 2+2 - bryan@Z1 11:38:31 04/23/10 Thanks for all the suggestions...Dwayne - dwayne 12:13:16 04/23/10 I've got a 2+2 with the Z1 DS... - xpwarrior 19:14:45 04/26/10
Post a Followup	You cannot reply to this message because you are not logged in.