Subject	Re: Re:
Posted by	WazTTed on December 17, 2009 at 8:58 PM
	This message has been viewed 227 times.
In Reply To	Re: posted by LJZTT on December 17, 2009 at 06:33 PM
Message	:Sorry, typical of me, when my mind is full of all this other stuff, simple things like hitting "printscreen" don't occur to me in the moment : :unplugging O2 sensors does nothing, unplugging TPS sensor(lower connector) stops the bouncing and the idle goes up near 3k, I realize I may have a boost leak, but I started with one. :code 55 : all your figures look ok. i had a faulty idle unit on my z.. it wouldnt change the idle even when u turned the screw ... could be your issue
Follow Ups	Running out of time to get Z sorted out - LJZTT 17:38:32 12/17/09 Re: Running out of time to get Z sorted out - WazTTed 17:57:17 12/17/09 Re: - LJZTT 18:33:33 12/17/09 before, the idle screw was threaded in pretty far, I tried - LJZTT 18:37:35 12/17/09 Just double checking -- when messing with the idle - jzack 19:38:37 12/17/09 I did not, I believe it can be turned off via Datascan tho - LJZTT 20:00:49 12/17/09 Just mentioning because that's the procedure for - jzack 20:50:20 12/17/09 Re: Just mentioning because that's the procedure for - LJZTT 22:23:13 12/17/09 Just for grins -- disconnect the TPS and then the - jzack 16:33:26 12/18/09 Re: Re: - WazTTed 20:58:22 12/17/09 Just finished running the "hunting" checklist from FSM - LJZTT 19:48:27 12/17/09 datalog once warmed, driven slowly around the block - LJZTT 19:58:44 12/17/09 Re: are your throttle plates opened? it seems you are - tognot 20:27:48 12/17/09 Throttle body butterflies... - ZTurboFan 21:37:48 12/17/09 the air leak could easily be responsible for your idle - surfer31337 20:30:36 12/17/09 how can I know if I have resolved the high idle if it wont - LJZTT 22:26:38 12/17/09 OK. this is EXACTLY what you should do (in this order) - surfer31337 23:19:43 12/17/09 Yeah, and I really like #1. - ZTurboFan 00:41:15 12/18/09 Re: - LJZTT 02:23:37 12/18/09 One thing I found - Stadsport (PHX) 20:38:16 12/17/09 @#$%ing FUEL LEAK.......puddle forming under the car - LJZTT 22:17:10 12/17/09 Sort of same boat. - Jehannum 12:54:28 12/18/09 RESOLVED....finally - LJZTT 02:00:14 12/19/09 So after you repulled and fixed the fuel leak, your - BoneZ 09:31:17 12/19/09 as luck would have it, I am back again with high idle - LJZTT 11:46:39 12/19/09 update: seems I have a sticky throttle that I cant figure - LJZTT 16:56:01 12/20/09 Re: update: seems I have a sticky throttle that I cant figure - WazTTed 18:49:08 12/20/09 yes, I said in the post it wants to stick around 2k after - LJZTT 19:14:02 12/20/09
Post a Followup	You cannot reply to this message because you are not logged in.