Subject	the air leak could easily be responsible for your idle
Posted by	surfer31337 on December 17, 2009 at 8:30 PM
	This message has been viewed 207 times.
In Reply To	Running out of time to get Z sorted out posted by LJZTT on December 17, 2009 at 05:38 PM
Message	issues. after you replaced the plenum gasket you need to obtain the use of an air compressor to perform another boost leak test. don't even bother replacing any electronic parts until you are 100% sure there are no more air leaks. BTW, if referencing the FSM I suggest you follow the steps from EF&EC 64 (High Idling after Warm-up) first and then EF & EC 67 (Unstable Idle).
Follow Ups	Running out of time to get Z sorted out - LJZTT 17:38:32 12/17/09 Re: Running out of time to get Z sorted out - WazTTed 17:57:17 12/17/09 Re: - LJZTT 18:33:33 12/17/09 before, the idle screw was threaded in pretty far, I tried - LJZTT 18:37:35 12/17/09 Just double checking -- when messing with the idle - jzack 19:38:37 12/17/09 I did not, I believe it can be turned off via Datascan tho - LJZTT 20:00:49 12/17/09 Just mentioning because that's the procedure for - jzack 20:50:20 12/17/09 Re: Just mentioning because that's the procedure for - LJZTT 22:23:13 12/17/09 Just for grins -- disconnect the TPS and then the - jzack 16:33:26 12/18/09 Re: Re: - WazTTed 20:58:22 12/17/09 Just finished running the "hunting" checklist from FSM - LJZTT 19:48:27 12/17/09 datalog once warmed, driven slowly around the block - LJZTT 19:58:44 12/17/09 Re: are your throttle plates opened? it seems you are - tognot 20:27:48 12/17/09 Throttle body butterflies... - ZTurboFan 21:37:48 12/17/09 the air leak could easily be responsible for your idle - surfer31337 20:30:36 12/17/09 how can I know if I have resolved the high idle if it wont - LJZTT 22:26:38 12/17/09 OK. this is EXACTLY what you should do (in this order) - surfer31337 23:19:43 12/17/09 Yeah, and I really like #1. - ZTurboFan 00:41:15 12/18/09 Re: - LJZTT 02:23:37 12/18/09 One thing I found - Stadsport (PHX) 20:38:16 12/17/09 @#$%ing FUEL LEAK.......puddle forming under the car - LJZTT 22:17:10 12/17/09 Sort of same boat. - Jehannum 12:54:28 12/18/09 RESOLVED....finally - LJZTT 02:00:14 12/19/09 So after you repulled and fixed the fuel leak, your - BoneZ 09:31:17 12/19/09 as luck would have it, I am back again with high idle - LJZTT 11:46:39 12/19/09 update: seems I have a sticky throttle that I cant figure - LJZTT 16:56:01 12/20/09 Re: update: seems I have a sticky throttle that I cant figure - WazTTed 18:49:08 12/20/09 yes, I said in the post it wants to stick around 2k after - LJZTT 19:14:02 12/20/09
Post a Followup	You cannot reply to this message because you are not logged in.