Subject	Re: vid
Posted by	ZTurboFan on December 17, 2009 at 6:41 PM
	This message has been viewed 155 times.
In Reply To	vid posted by Andrewhuffman on December 17, 2009 at 06:32 PM
Message	MAF voltage is what? MAF is plugged in? You actually verify it is within spec and that MAF sensor is in fact OK? I know you said it was changed. But are both MAF's known goods? Test'em anyhow. The only thing strange is usually when the MAF is bad, it does that same kind of thing only faster. Have you done a boost leak test?
Follow Ups	New motor wont start. - Andrewhuffman 09:15:09 12/17/09 Are the plugs soaked from gas? (n/m) - Josher 09:22:25 12/17/09 Sounds like your plugs are fouled, also check if your maf - Ice95z 09:42:23 12/17/09 check to see if you reversed the fuel line by accident - NobleZ 09:49:55 12/17/09 Fuel lines are straight. The plugs are soaked... - Andrewhuffman 10:15:28 12/17/09 Are all six are soaked? - CaliguyPurdue (Selin Design) 11:20:12 12/17/09 changed the MAF, changed PTU. - Andrewhuffman 10:31:36 12/17/09 did you check the CAS? also, did you change the fuel filter? - NobleZ 10:52:26 12/17/09 Try posting in the technical forum. Its why its there. (n/m) - z32z 11:42:24 12/17/09 This is the technical forum . Technically speaking ! (n/m) - xteam300tt 13:32:22 12/17/09 This post was in the General forum before it was moved here. (n/m) - NytWolf 17:25:52 12/17/09 Recheck your timing belt - NytWolf 11:43:41 12/17/09 all 6 were soaked. new fuel filter. checked CAS. - Andrewhuffman 15:33:17 12/17/09 You're not listening nor do you comprehend a 4-stroke motor (n/m) - NytWolf 16:54:26 12/17/09 The timing belt is not wrong! - Andrewhuffman 17:11:02 12/17/09 LOL -- How do you know it's not wrong? - NytWolf 17:21:29 12/17/09 Re: LOL -- How do you know it's not wrong? - canyoncarver 22:13:46 12/18/09 It Lives!~!!! - Andrewhuffman 18:16:20 12/17/09 Re: It Lives!~!!! - Andrewhuffman 19:11:32 12/17/09 vid - Andrewhuffman 18:32:06 12/17/09 Re: vid - ZTurboFan 18:41:12 12/17/09 vid - Andrewhuffman 18:54:48 12/17/09 Re: vid - ZTurboFan 19:01:49 12/17/09 Re: Re: vid - Andrewhuffman 19:12:21 12/17/09 No exhaust... - ZTurboFan 19:40:43 12/17/09 Re: No exhaust... - Andrewhuffman 20:04:11 12/17/09 Re: Re: No exhaust... - ZTurboFan 20:20:30 12/17/09 Re: Re: Re: No exhaust... - Andrewhuffman 23:29:29 12/17/09 Well... - ZTurboFan 00:39:36 12/18/09 Re: Well... - Andrewhuffman 11:12:20 12/18/09 Update - Andrewhuffman 14:31:23 12/18/09 Like I said, timing issue - canyoncarver 17:10:04 12/18/09 Timing - ZTurboFan 19:48:11 12/18/09 Re: Timing - Andrewhuffman 01:27:33 12/19/09 Re: Re: Timing - Andrewhuffman 01:28:47 12/19/09 Assumptions...are...BAD - ZTurboFan 10:55:21 12/19/09 Re: Assumptions...are...BAD - Andrewhuffman 14:09:29 12/19/09 Next Steps - ZTurboFan 16:06:12 12/19/09 Re: Next Steps - Andrewhuffman 20:37:50 12/19/09 1 Year+ - ZTurboFan 21:40:21 12/19/09 Timing - Andrewhuffman 11:18:05 12/20/09 Ok. Good. - ZTurboFan 11:49:58 12/20/09 Update - Andrewhuffman 13:51:01 12/20/09 Imprint, not inpring. - Andrewhuffman 13:56:11 12/20/09 #1-90, #3-60, #5-90 - Andrewhuffman 14:02:07 12/20/09 Re: #1-90, #3-60, #5-90 - ZTurboFan 14:29:26 12/20/09 Re: Re: #1-90, #3-60, #5-90 - Andrewhuffman 14:39:43 12/20/09 That's a bummer... - ZTurboFan 16:41:00 12/20/09 Re: That's a bummer... - Andrewhuffman 20:45:24 12/20/09 Well...one more... - ZTurboFan 09:36:27 12/21/09 Update - Andrewhuffman 14:18:06 12/21/09 Re: Update - Andrewhuffman 14:33:22 12/21/09 My Thoughts... - ZTurboFan 15:27:14 12/21/09 Re: My Thoughts... - Andrewhuffman 15:53:29 12/21/09 Lifter Rebuild - ZTurboFan 22:13:39 12/21/09 Oh, and good on the cams - ZTurboFan 22:15:40 12/21/09 It Lives!~!!!... again - Andrewhuffman 19:57:11 01/01/10 WTF you are an idiot. This assuming - dream Z (MD) 02:37:57 01/02/10 Re: WTF you are an idiot. This assuming - Andrewhuffman 06:03:19 01/02/10 Get a bigger computer screen. - dream Z (MD) 11:41:00 01/02/10
Post a Followup	You cannot reply to this message because you are not logged in.