Subject	changed the MAF, changed PTU.
Posted by	Andrewhuffman on December 17, 2009 at 10:31 AM
	This message has been viewed 107 times.
In Reply To	New motor wont start. posted by Andrewhuffman on December 17, 2009 at 09:15 AM
Message	It seems like the spark isnt strong enough or the fuel isn't burning properly. The car sat for 2 years, i draind the gas and put 5 gal of new 93oct. I then disconnected the fuel line and pumped the line out. I dodn't get all the fuel out, but i haoped to dilute the bad gas with good gas. Also the new harness had been cut by the maf, i soldiered and wrapped it back up there.
Follow Ups	New motor wont start. - Andrewhuffman 09:15:09 12/17/09 Are the plugs soaked from gas? (n/m) - Josher 09:22:25 12/17/09 Sounds like your plugs are fouled, also check if your maf - Ice95z 09:42:23 12/17/09 check to see if you reversed the fuel line by accident - NobleZ 09:49:55 12/17/09 Fuel lines are straight. The plugs are soaked... - Andrewhuffman 10:15:28 12/17/09 Are all six are soaked? - CaliguyPurdue (Selin Design) 11:20:12 12/17/09 changed the MAF, changed PTU. - Andrewhuffman 10:31:36 12/17/09 did you check the CAS? also, did you change the fuel filter? - NobleZ 10:52:26 12/17/09 Try posting in the technical forum. Its why its there. (n/m) - z32z 11:42:24 12/17/09 This is the technical forum . Technically speaking ! (n/m) - xteam300tt 13:32:22 12/17/09 This post was in the General forum before it was moved here. (n/m) - NytWolf 17:25:52 12/17/09 Recheck your timing belt - NytWolf 11:43:41 12/17/09 all 6 were soaked. new fuel filter. checked CAS. - Andrewhuffman 15:33:17 12/17/09 You're not listening nor do you comprehend a 4-stroke motor (n/m) - NytWolf 16:54:26 12/17/09 The timing belt is not wrong! - Andrewhuffman 17:11:02 12/17/09 LOL -- How do you know it's not wrong? - NytWolf 17:21:29 12/17/09 Re: LOL -- How do you know it's not wrong? - canyoncarver 22:13:46 12/18/09 It Lives!~!!! - Andrewhuffman 18:16:20 12/17/09 Re: It Lives!~!!! - Andrewhuffman 19:11:32 12/17/09 vid - Andrewhuffman 18:32:06 12/17/09 Re: vid - ZTurboFan 18:41:12 12/17/09 vid - Andrewhuffman 18:54:48 12/17/09 Re: vid - ZTurboFan 19:01:49 12/17/09 Re: Re: vid - Andrewhuffman 19:12:21 12/17/09 No exhaust... - ZTurboFan 19:40:43 12/17/09 Re: No exhaust... - Andrewhuffman 20:04:11 12/17/09 Re: Re: No exhaust... - ZTurboFan 20:20:30 12/17/09 Re: Re: Re: No exhaust... - Andrewhuffman 23:29:29 12/17/09 Well... - ZTurboFan 00:39:36 12/18/09 Re: Well... - Andrewhuffman 11:12:20 12/18/09 Update - Andrewhuffman 14:31:23 12/18/09 Like I said, timing issue - canyoncarver 17:10:04 12/18/09 Timing - ZTurboFan 19:48:11 12/18/09 Re: Timing - Andrewhuffman 01:27:33 12/19/09 Re: Re: Timing - Andrewhuffman 01:28:47 12/19/09 Assumptions...are...BAD - ZTurboFan 10:55:21 12/19/09 Re: Assumptions...are...BAD - Andrewhuffman 14:09:29 12/19/09 Next Steps - ZTurboFan 16:06:12 12/19/09 Re: Next Steps - Andrewhuffman 20:37:50 12/19/09 1 Year+ - ZTurboFan 21:40:21 12/19/09 Timing - Andrewhuffman 11:18:05 12/20/09 Ok. Good. - ZTurboFan 11:49:58 12/20/09 Update - Andrewhuffman 13:51:01 12/20/09 Imprint, not inpring. - Andrewhuffman 13:56:11 12/20/09 #1-90, #3-60, #5-90 - Andrewhuffman 14:02:07 12/20/09 Re: #1-90, #3-60, #5-90 - ZTurboFan 14:29:26 12/20/09 Re: Re: #1-90, #3-60, #5-90 - Andrewhuffman 14:39:43 12/20/09 That's a bummer... - ZTurboFan 16:41:00 12/20/09 Re: That's a bummer... - Andrewhuffman 20:45:24 12/20/09 Well...one more... - ZTurboFan 09:36:27 12/21/09 Update - Andrewhuffman 14:18:06 12/21/09 Re: Update - Andrewhuffman 14:33:22 12/21/09 My Thoughts... - ZTurboFan 15:27:14 12/21/09 Re: My Thoughts... - Andrewhuffman 15:53:29 12/21/09 Lifter Rebuild - ZTurboFan 22:13:39 12/21/09 Oh, and good on the cams - ZTurboFan 22:15:40 12/21/09 It Lives!~!!!... again - Andrewhuffman 19:57:11 01/01/10 WTF you are an idiot. This assuming - dream Z (MD) 02:37:57 01/02/10 Re: WTF you are an idiot. This assuming - Andrewhuffman 06:03:19 01/02/10 Get a bigger computer screen. - dream Z (MD) 11:41:00 01/02/10
Post a Followup	You cannot reply to this message because you are not logged in.