TwinTurbo.NET: Nissan 300ZX forum - The weld was not clean. Get someone who knows what they
Subject
The weld was not clean. Get someone who knows what they
Posted by
jcieslik
on February 01, 2008 at 10:41 PM
This message has been viewed
69
times.
In Reply To
SZR: rounded/stripped transmission plug
posted by RedSER13
on January 30, 2008 at 12:29 PM
Message
are doing. When you weld a nut/socket/etc it needs to be clean, if it broke off, the weld was bad most likely from grease and oxidation that was not removed. Dremel that thing shiney and clean and have them put some heat into it.
Jeff Cieslik
Follow Ups
SZR: rounded/stripped transmission plug
-
RedSER13
12:29:11 01/30/08
Welded socket didn't work?
-
BradZ (FL)
12:34:59 01/30/08
I'd make a slit right though its face with a dremel
-
ZEngineer
12:37:33 01/30/08
Screwdriver to remove that? What you been smoking today?
-
spicyZ
12:46:54 01/30/08
*big screwdriver. Read the post, n99b (n/m)
-
ZEngineer
12:48:31 01/30/08
Attn: ZNongineer
-
Kenny
12:52:00 01/30/08
Pfft, shows how much experience you have with slits. (n/m)
-
BradZ (FL)
12:55:00 01/30/08
ok, fine, it was a bad idea, call off the dogs (n/m)
-
ZEngineer
13:00:25 01/30/08
We're not done with you yet. (n/m)
-
Kenny
13:12:25 01/30/08
uhmm. George, besides the bad idea of using a big screw
-
Cap927(Boston)
14:12:02 01/30/08
yes, this is the one. (n/m)
-
RedSER13
14:34:11 01/30/08
Nice try! (n/m)
-
Spongerider :)
14:37:07 01/30/08
weld socket, tighten then loosen (n/m)
-
ZiNnYc
12:40:44 01/30/08
2nd on the tighten first (n/m)
-
spicyZ
12:46:21 01/30/08
Try PB blaster or Freeze off, should be in any auto store (n/m)
-
DoodMon(SD)
12:43:22 01/30/08
What happened to the welded socket?
-
bliZard
13:13:17 01/30/08
the weld just broke and kissed my $10 goodbye. (n/m)
-
RedSER13
14:35:34 01/30/08
Oh I remember doing this... Not fun.
-
MixManMash
13:48:01 01/30/08
OOO! A MaGiCaL StOrY! (n/m)
-
ZiNnYc
13:51:46 01/30/08
Helpful! :-) (n/m)
-
spicyZ
14:12:38 01/30/08
nice. i can use this. (n/m)
-
RedSER13
14:36:18 01/30/08
if welding a socket to the plug failed probably because
-
Cap927(Boston)
14:24:59 01/30/08
thanks. i'll look around for this tool. (n/m)
-
RedSER13
14:37:43 01/30/08
it's actually not a tool, but square metal stock
-
Cap927(Boston)
14:49:26 01/30/08
i also tried heating up the plug before loosening.
-
RedSER13
14:42:16 01/30/08
yeah, the plug needs to be cold and the tranny hot.
-
BlackholeZ
15:07:53 01/30/08
Buy a suction device and use the vent hole to suck
-
spicyZ
15:09:43 01/30/08
Have you ever had this out before?
-
bliZard
15:39:46 01/30/08
yes, i've had it out before and it wasn't rounded.
-
RedSER13
15:52:32 01/30/08
Use PB blaster.. and heat that shiz up..
-
Kong ZTT GT28RS MD
15:17:56 01/30/08
I had the same problem this week....
-
Z1rider
15:32:06 01/30/08
Another ting I've used as a last resort
-
BlackholeZ
17:15:25 01/30/08
Ive had some good luck with an air hammer.
-
Knapper411
18:38:37 01/30/08
How about get a big easy-out and cut it off so you
-
Audioquest
21:30:04 01/30/08
If you are just trying to change the trans oil
-
goldentt
08:24:39 01/31/08
If you are still having problems, try this way.
-
dswtflip4u
21:50:20 01/31/08
The weld was not clean. Get someone who knows what they -
jcieslik
22:41:38 02/01/08
Post a
Followup
You cannot reply to this message because you are not
logged in
.