Subject	Yes - the angle of the plies offsets the angle of the
Posted by	Bernie (NoVA) on January 16, 2008 at 11:52 AM
	This message has been viewed 71 times.
In Reply To	Re: There are pleny of similar but cheaper options out there posted by Fly-Surf on January 16, 2008 at 08:57 AM
Message	connector and you can pretty much pull straight up. HI Overdrive Water Pump Pullies Are Here! Bernie Bilski berniebilski@cox.net 1995 Nissan 300ZX TwinTurbo in Cobalt Green 1997 Nissan 240SX SE in Ultra Red (some assembly required) 1995 Nissan Pick-Up XE in Super Black ZCCNV #390 ~ ECZA #368 Need INSTALLS, DIAGNOSTICS, SERVICE or PARTS in the NoVA/DC/MD area? Please email me or check out my current inventory.
Follow Ups	Injector removal secrets?...dremel technique - Fly-Surf 20:23:24 01/15/08 my best tool for that is a pair of long nose vise grips - Guapo 20:39:38 01/15/08 Re: my best tool for that is a pair of long nose vise grips - Fly-Surf 07:52:11 01/16/08 I wrap the jaws mine with some tape to soften. - mossyoak 13:40:51 01/16/08 let it soak overnight in the PB Blaster, try again tomorrow - robo (sebring1970) 22:22:53 01/15/08 Some one here said they drilled - 818TTZ(SoCal) 22:56:40 01/15/08 That's usually my "all the plastic has broken off" fall back (n/m) - Bernie (NoVA) 23:20:09 01/15/08 THANKS 818TTZ and Bernie! - Fly-Surf 07:53:53 01/16/08 Still no luck...any warnings about drilling? - Fly-Surf 19:35:29 01/16/08 If anthing the fuel pressure would help push it out. - Bernie (NoVA) 23:37:47 01/16/08 Thanks...maybe I should pressurize the system :-) (n/m) - Fly-Surf 09:21:56 01/17/08 might be time to say "uncle" and pull the plenum (n/m) - robo (sebring1970) 01:28:30 01/17/08 I'm almost at that point! But... - Fly-Surf 09:23:40 01/17/08 Okay...now what? - Fly-Surf 19:05:49 01/18/08 Did you hit it somewhere as it came out or was it just - Bernie (NoVA) 20:04:35 01/18/08 Re: Did you hit it somewhere as it came out or was it just - Fly-Surf 20:16:00 01/18/08 Bottom line...If its flaoting in the fuel rail... - Fly-Surf 20:25:59 01/18/08 Looks like I'm done...car is back to NORMAL! - Fly-Surf 08:46:22 01/20/08 9 times out of 10 I use something like this, grab the injec- - Bernie (NoVA) 23:19:26 01/15/08 2nd - ZXRider(SoCal) 03:14:12 01/16/08 Matco..."PNP-8"? - Fly-Surf 08:03:06 01/16/08 There are pleny of similar but cheaper options out there - Bernie (NoVA) 08:12:42 01/16/08 Re: There are pleny of similar but cheaper options out there - Fly-Surf 08:57:07 01/16/08 Yes - the angle of the plies offsets the angle of the - Bernie (NoVA) 11:52:44 01/16/08 Harbor Freight is cheap for those - robo (sebring1970) 16:54:34 01/16/08 dont forget 1/8 inch counterclockwise/clockwise - mossyoak 13:35:13 01/16/08
Post a Followup	You cannot reply to this message because you are not logged in.