Subject	There should be NO spin testing of NEW CHRA
Posted by	Chip(GinnMotorSports) on September 15, 2003 at 12:29 PM
	This message has been viewed 33 times.
In Reply To	Let's not forget about the ASSEMBLY of the turbos posted by SeedyROM on September 15, 2003 at 12:14 PM
Message	that is what the factory does after assembly. Now if the shop is screwing with the CHRA (putting different wheels on it) AVOID them, high failure rate on anything done to the Garrett CHRA.
Follow Ups	Z1 Turbos vs. GT2530's (Z1 guys, add info here) - ZLover4Life 10:47:11 09/15/03 also, are there any suppliers for Greg Dupree DP's? - ZLover4Life 10:52:27 09/15/03 We carry them. - Chip(GinnMotorSports) 11:00:24 09/15/03 hey Chip, how do your GT500's compare? - ZLover4Life 11:05:24 09/15/03 Still working on them, BUT they will be MUCH smaller - Chip(GinnMotorSports) 11:16:30 09/15/03 HKS does not make turbos, they market turbos. - Chip(GinnMotorSports) 10:59:16 09/15/03 ok, so that takes out the reputation factor (n/m) - ZLover4Life 11:01:59 09/15/03 One factor involved, make sure thay use a new CHRA. - Chip(GinnMotorSports) 11:03:46 09/15/03 thanks for the advice, check my reply to your DP post (n/m) - ZLover4Life 11:06:16 09/15/03 Let's not forget about the ASSEMBLY of the turbos - SeedyROM 12:14:07 09/15/03 There should be NO spin testing of NEW CHRA - Chip(GinnMotorSports) 12:29:53 09/15/03 Good info. Still assembly though. - SeedyROM 14:22:06 09/15/03 I agree, A mismachined housing is very bad. (n/m) - Chip(GinnMotorSports) 14:54:10 09/15/03 The CHRA doesn't include the compressor wheel - Carlos Ramirez 14:54:03 09/15/03 All of the CHRA's that I have ordered came with both wheels - Chip(GinnMotorSports) 15:03:11 09/15/03 But, If it does not have the compressor wheel, it will need - Chip(GinnMotorSports) 15:04:41 09/15/03 Hmmm maybe thats only the case on T2 CHRA - Carlos Ramirez 15:25:43 09/15/03 I wish that I had an excuse to buy a TO4 CHRA! - Chip(GinnMotorSports) 17:14:39 09/15/03 no not turbonetics.. (n/m) - Carlos Ramirez 01:08:27 09/16/03 Re: Z1 Turbos vs. GT2530's (Z1 guys, add info here) - kuah@splparts.com 11:25:29 09/15/03 how long does it normally take you guys to ship GT2530's? - ZLover4Life 11:33:11 09/15/03 Shipping is $10, and typically ships in about 2 weeks (n/m) - kuah@splparts.com 11:35:25 09/15/03 Check with George@boostsolutions also. He had them in stock - Scotts94z32 12:17:23 09/15/03 you may have just saved me $56, might be time to negotiate (n/m) - ZLover4Life 12:41:17 09/15/03 So you'll give out proprietary information on an open - AshsZ of Z1Motorsports.com 12:56:32 09/15/03 I will have dyno results for those turbos in a day or two. - AshsZ of Z1Motorsports.com 12:07:47 09/15/03
Post a Followup	You cannot reply to this message because you are not logged in.