Subject	when I got mine, I just got a piece of PVC, something along
Posted by	JMT-Z(St. Louis) on September 03, 2003 at 3:29 PM
	This message has been viewed 33 times.
In Reply To	Need solution for shifter boot posted by Nitroedge-94 300ZX TT Black on September 03, 2003 at 10:53 AM
Message	the lines of 1" then I just used my dremel to basically make a smaller version of the original ring. Works great. "If everything seems under control, you're just not going fast enough." - Mario Andretti
Follow Ups	Need solution for shifter boot - Nitroedge-94 300ZX TT Black 10:53:42 09/03/03 go back to the factory knob :) (n/m) - imahurtchu 11:01:15 09/03/03 Buy a MOMO shift boot. - BudManZ 11:21:53 09/03/03 i soldered 2 washers on to keep mine on. - odium69 11:35:25 09/03/03 Great suggestion, thx... so you got the same "stupid shifter - Nitroedge-94 300ZX TT Black 11:43:33 09/03/03 look, you stupid asshat... - nixit 11:59:02 09/03/03 I'm still trying to figure out - Guapo 12:04:56 09/03/03 Wheelskins.com, leather wheel wraps man... (n/m) - Nitroedge-94 300ZX TT Black 12:15:14 09/03/03 We know what it is, but their product sucks. (n/m) - YugoBernie (NoVA) 12:35:05 09/03/03 So voice the alternative, what product is better Yugo? (n/m) - Nitroedge-94 300ZX TT Black 13:59:18 09/03/03 stock steering wheel or Aspendog recover (n/m) - fourZero 14:08:21 09/03/03 A high quality recover from www.importsextreme.com - YugoBernie (NoVA) 16:05:26 09/03/03 FOOOOOOOD Fiiiiiiight!!!!!!!!!!!1 (n/m) - unluky 12:14:15 09/03/03 <throws cheeseburger> (n/m) - Nitroedge-94 300ZX TT Black 12:17:48 09/03/03 Ya the suggestions were helpful but what's with the>>> - Nitroedge-94 300ZX TT Black 12:14:17 09/03/03 Bad form. - Malukalu99 13:21:07 09/03/03 Sh|t I'm married too, better tell the wife I swing both>>> - Nitroedge-94 300ZX TT Black 13:23:18 09/03/03 thanks for the insite. - nixit 14:41:45 09/03/03 Requiring a ballast means its not HID? What? - Malukalu99 16:08:52 09/03/03 Why not remove the shift boot and restitch the - Milo (San Antonio, TX.) 11:37:49 09/03/03 Hey Guapo, check this... since this post hit I got>>> - Nitroedge-94 300ZX TT Black 11:41:48 09/03/03 You should have quit while you were ahead.... - Dave N 12:42:22 09/03/03 I'm cool with it, but #2) rice mods, that is hard cuz>>> - Nitroedge-94 300ZX TT Black 13:21:59 09/03/03 As long as you're not looking for the approval of others - Dave N 14:55:55 09/03/03 I'm certainly not looking for the approval of the guys here> - Nitroedge-94 300ZX TT Black 15:12:33 09/03/03 Huge kudos via email for Greg Dupree and Z1... thx>>> - Nitroedge-94 300ZX TT Black 12:17:21 09/03/03 you're an idiot.... - Spee 12:29:46 09/03/03 shrug ... - Guapo 12:37:27 09/03/03 we are on the same page then. - Spee 12:49:38 09/03/03 remove stupid shifter, and my wheelskin msg, you>>> - Nitroedge-94 300ZX TT Black 13:18:58 09/03/03 when the hell did I say that? (n/m) - Guapo 13:37:53 09/03/03 Indiglo is for watches (n/m) - Nitroedge-94 300ZX TT Black 13:58:44 09/03/03 that's correct (n/m) - Spee 15:43:10 09/03/03 Indiglo is pretty gay looking, has a blue-green tint. (n/m) - Malukalu99 16:07:40 09/03/03 Invert the top of the boot around a rubber O-ring. If - sebring1970 (robo) 12:20:34 09/03/03 you might want to install your shifter right... - Spee 12:26:02 09/03/03 when I got mine, I just got a piece of PVC, something along - JMT-Z(St. Louis) 15:29:30 09/03/03 very very very easy fix, did this when i put on my old Z31 - ENVYMYZ 01:51:34 09/04/03
Post a Followup	You cannot reply to this message because you are not logged in.