TwinTurbo.NET: Nissan 300ZX forum - Been covered before...I have 2 Z's. (n/m)
Subject
Been covered before...I have 2 Z's. (n/m)
Posted by
Woody75 (Denver)
on August 14, 2003 at 4:57 PM
This message has been viewed
21
times.
In Reply To
Do you have one cleared tail and one not cleared? (n/m)
posted by BigTDogg
on August 14, 2003 at 04:28 PM
Message
Follow Ups
Finally, my MS manifolds are here (Dial-up do not attempt)
-
Woody75 (Denver)
08:47:54 08/14/03
Sweetness Tim! Your patience has run out...time to drive! :) (n/m)
-
5150Z
08:58:29 08/14/03
Drive? I just want to be able to back it out to wash it :) (n/m)
-
Woody75 (Denver)
09:01:46 08/14/03
Bout damn time... (n/m)
-
LordZ
09:50:18 08/14/03
In that last pic does that hole go all the way through? >>
-
SlicktopTT
09:57:48 08/14/03
You mean where the turbo mounting stud goes? (n/m)
-
Woody75 (Denver)
10:02:40 08/14/03
Yup I guess that's what it is. (n/m)
-
SlicktopTT
10:11:46 08/14/03
I think once its back in I will have to smooth it down.
-
Woody75 (Denver)
10:19:23 08/14/03
Ok, few questions...
-
BigTDogg
09:59:17 08/14/03
Mike Smith did the manifold work.
-
Woody75 (Denver)
10:07:03 08/14/03
Get to work...slacker!! (n/m)
-
BigRob
10:08:05 08/14/03
Thanks for the info. (n/m)
-
BigTDogg
10:09:01 08/14/03
looks good Tim (n/m)
-
aliaZ (IC Nazi)
10:08:18 08/14/03
How do they compare to yours? Do you approve? (n/m)
-
Woody75 (Denver)
10:11:47 08/14/03
I definitely approve. What are your impressions
-
aliaZ (IC Nazi)
10:30:45 08/14/03
Seems like pretty good stuff.
-
Woody75 (Denver)
10:44:47 08/14/03
Do you have one cleared tail and one not cleared? (n/m)
-
BigTDogg
16:28:29 08/14/03
Been covered before...I have 2 Z's. (n/m) -
Woody75 (Denver)
16:57:02 08/14/03
I knew that, I just wasn't fast enough to figure out
-
BigTDogg
17:48:52 08/14/03
Very nice! (n/m)
-
Arthur
10:18:49 08/14/03
Very nice Tim!! Wish I was in CO for a ride when its done! (n/m)
-
therinL
10:30:07 08/14/03
very nice! (n/m)
-
Wagz
11:17:21 08/14/03
Awesome! VERY nice work my Mr Smith
-
Turbodog (CT)
13:06:32 08/14/03
Your torque numbers are off, they're slightly higher
-
BigTDogg
13:19:20 08/14/03
Now THAT is how it's done. (n/m)
-
SeedyROM
13:15:53 08/14/03
Three years without a running Z for me. Good luck! (n/m)
-
ProfeZZor X
13:59:23 08/14/03
Post a
Followup
You cannot reply to this message because you are not
logged in
.