Subject	Awesome! VERY nice work my Mr Smith
Posted by	Turbodog (CT) on August 14, 2003 at 1:06 PM
	This message has been viewed 28 times.
In Reply To	Finally, my MS manifolds are here (Dial-up do not attempt) posted by Woody75 (Denver) on August 14, 2003 at 08:47 AM
Message	ah, no big deal missing the summer. It's been too dam hot to go boosting hard anyway. Might as well shoot for the fall, when it's more fun to drive anyway right?? Last dyno: 468-rwhp 605-lbs torque(!) On 94 octane @ 19psi Last 1/4 mi: 12.55 & 117mph (w/clutch slipping)
Follow Ups	Finally, my MS manifolds are here (Dial-up do not attempt) - Woody75 (Denver) 08:47:54 08/14/03 Sweetness Tim! Your patience has run out...time to drive! :) (n/m) - 5150Z 08:58:29 08/14/03 Drive? I just want to be able to back it out to wash it :) (n/m) - Woody75 (Denver) 09:01:46 08/14/03 Bout damn time... (n/m) - LordZ 09:50:18 08/14/03 In that last pic does that hole go all the way through? >> - SlicktopTT 09:57:48 08/14/03 You mean where the turbo mounting stud goes? (n/m) - Woody75 (Denver) 10:02:40 08/14/03 Yup I guess that's what it is. (n/m) - SlicktopTT 10:11:46 08/14/03 I think once its back in I will have to smooth it down. - Woody75 (Denver) 10:19:23 08/14/03 Ok, few questions... - BigTDogg 09:59:17 08/14/03 Mike Smith did the manifold work. - Woody75 (Denver) 10:07:03 08/14/03 Get to work...slacker!! (n/m) - BigRob 10:08:05 08/14/03 Thanks for the info. (n/m) - BigTDogg 10:09:01 08/14/03 looks good Tim (n/m) - aliaZ (IC Nazi) 10:08:18 08/14/03 How do they compare to yours? Do you approve? (n/m) - Woody75 (Denver) 10:11:47 08/14/03 I definitely approve. What are your impressions - aliaZ (IC Nazi) 10:30:45 08/14/03 Seems like pretty good stuff. - Woody75 (Denver) 10:44:47 08/14/03 Do you have one cleared tail and one not cleared? (n/m) - BigTDogg 16:28:29 08/14/03 Been covered before...I have 2 Z's. (n/m) - Woody75 (Denver) 16:57:02 08/14/03 I knew that, I just wasn't fast enough to figure out - BigTDogg 17:48:52 08/14/03 Very nice! (n/m) - Arthur 10:18:49 08/14/03 Very nice Tim!! Wish I was in CO for a ride when its done! (n/m) - therinL 10:30:07 08/14/03 very nice! (n/m) - Wagz 11:17:21 08/14/03 Awesome! VERY nice work my Mr Smith - Turbodog (CT) 13:06:32 08/14/03 Your torque numbers are off, they're slightly higher - BigTDogg 13:19:20 08/14/03 Now THAT is how it's done. (n/m) - SeedyROM 13:15:53 08/14/03 Three years without a running Z for me. Good luck! (n/m) - ProfeZZor X 13:59:23 08/14/03
Post a Followup	You cannot reply to this message because you are not logged in.