Subject	Ok, few questions...
Posted by	BigTDogg on August 14, 2003 at 9:59 AM
	This message has been viewed 35 times.
In Reply To	Finally, my MS manifolds are here (Dial-up do not attempt) posted by Woody75 (Denver) on August 14, 2003 at 08:47 AM
Message	Where did you get those manifolds from? Cost? How much of an advantage is the polishing of the turbo housings? Looks like a killer setup, can't wait to see it run, and I'm sure you can't either. "...Downpipes own. They own everything...anything...all there ever was and will be...they should be stock on all cars. Screw the environment, emissions, noise! I love them...I shall name my first-born after them with glee..." - SeedyRom 05:13:20 10/03/02 "Ricers are idiots" - RezidentEvil "It's like if my girl desides to go on a weekend orgy because she needs to get it out of her F*&%$ing system, now would I want her back? I hope she had a great time. Because at that point I'll trade her in." - Cap927 09:41:06 12/13/02 “I don't haul around stuff in the Z. I have a daily driver for that! :) Besides my shotgun could still fit snugly behind my seat!” - dragonballz 5/23/2003 "a hair brush does make a nice didlo, but it fixes your hair even better" -Nixit 6/2/2003
Follow Ups	Finally, my MS manifolds are here (Dial-up do not attempt) - Woody75 (Denver) 08:47:54 08/14/03 Sweetness Tim! Your patience has run out...time to drive! :) (n/m) - 5150Z 08:58:29 08/14/03 Drive? I just want to be able to back it out to wash it :) (n/m) - Woody75 (Denver) 09:01:46 08/14/03 Bout damn time... (n/m) - LordZ 09:50:18 08/14/03 In that last pic does that hole go all the way through? >> - SlicktopTT 09:57:48 08/14/03 You mean where the turbo mounting stud goes? (n/m) - Woody75 (Denver) 10:02:40 08/14/03 Yup I guess that's what it is. (n/m) - SlicktopTT 10:11:46 08/14/03 I think once its back in I will have to smooth it down. - Woody75 (Denver) 10:19:23 08/14/03 Ok, few questions... - BigTDogg 09:59:17 08/14/03 Mike Smith did the manifold work. - Woody75 (Denver) 10:07:03 08/14/03 Get to work...slacker!! (n/m) - BigRob 10:08:05 08/14/03 Thanks for the info. (n/m) - BigTDogg 10:09:01 08/14/03 looks good Tim (n/m) - aliaZ (IC Nazi) 10:08:18 08/14/03 How do they compare to yours? Do you approve? (n/m) - Woody75 (Denver) 10:11:47 08/14/03 I definitely approve. What are your impressions - aliaZ (IC Nazi) 10:30:45 08/14/03 Seems like pretty good stuff. - Woody75 (Denver) 10:44:47 08/14/03 Do you have one cleared tail and one not cleared? (n/m) - BigTDogg 16:28:29 08/14/03 Been covered before...I have 2 Z's. (n/m) - Woody75 (Denver) 16:57:02 08/14/03 I knew that, I just wasn't fast enough to figure out - BigTDogg 17:48:52 08/14/03 Very nice! (n/m) - Arthur 10:18:49 08/14/03 Very nice Tim!! Wish I was in CO for a ride when its done! (n/m) - therinL 10:30:07 08/14/03 very nice! (n/m) - Wagz 11:17:21 08/14/03 Awesome! VERY nice work my Mr Smith - Turbodog (CT) 13:06:32 08/14/03 Your torque numbers are off, they're slightly higher - BigTDogg 13:19:20 08/14/03 Now THAT is how it's done. (n/m) - SeedyROM 13:15:53 08/14/03 Three years without a running Z for me. Good luck! (n/m) - ProfeZZor X 13:59:23 08/14/03
Post a Followup	You cannot reply to this message because you are not logged in.