Subject	At least my engine lasted much longer than Bryan's
Posted by	MikeH(Twin GT35BB Incon Z) on August 01, 2003 at 12:51 PM
	This message has been viewed 40 times.
In Reply To	Did you take yours back to the same machine shop???---> posted by Kyle(Houston) on August 01, 2003 at 06:53 AM
Message	engine which YOUR machine shop did the work on. My engine lasted 5000 miles and I had a lot of boost runs before it went south. Bryan's engine didn't make it past one dyno session. My five remaining rod bearing were flawless compared to what Bryan's rod bearing are. I would say my machine shop did a better job than yours... but I am not going to use them again.. my decision.
Follow Ups	Officially starting project waste money - WhiteOutZ 20:13:10 07/31/03 More info - WhiteOutZ 20:16:39 07/31/03 Who's doing all the work for you? (n/m) - Z-king 20:21:30 07/31/03 I would like to know that bit of information as well. (n/m) - Bryan (AKA B-Ster) 20:38:59 07/31/03 easier said then done...best of luck to ya! (n/m) - Wagz 20:31:01 07/31/03 2nd (n/m) - CarbonZTT 22:20:53 07/31/03 Run from this project. (n/m) - Bryan (AKA B-Ster) 20:37:50 07/31/03 Seconded (n/m) - Import-Driven 20:38:59 07/31/03 LOL and 900RWHP by no means.. - Carlos Ramirez 20:45:20 07/31/03 Whatever, just spray some NOS,and freeze the Border :_) - George(boost-solutions.com) 20:47:12 07/31/03 yeah, it's not like you have a field of motors - Halo Z 20:55:49 07/31/03 I will bring the broom :-) (n/m) - Carlos Ramirez 21:01:49 07/31/03 Too funny!!! (n/m) - Bryan (AKA B-Ster) 22:13:36 07/31/03 Ash can tune it (n/m) - George(boost-solutions.com) 00:39:24 08/01/03 Bryan, there is no way back, dude:-) (n/m) - George(boost-solutions.com) 20:47:54 07/31/03 Why dont you get swain coating on pistons instead? (n/m) - BooZted 20:41:29 07/31/03 Just look at my profile, Bryan's, TTPete's,and Sparkies, and - George(boost-solutions.com) 20:49:45 07/31/03 I second and third that george.. but even good --->>> - 300zx.ca 20:58:31 07/31/03 damm I am always getting left out :-) I have 2835s too! - Carlos Ramirez 21:02:40 07/31/03 Yea, you and me are the red-headed step childs (n/m) - MikeH(Twin GT35BB Incon Z) 22:59:02 07/31/03 childs?? ;-P (n/m) - MaTT (90TT) 23:03:39 07/31/03 Yeah, but... - MaTT (90TT) 23:02:55 07/31/03 I got a whole new body kit planned after car is running ' (n/m) - Carlos Ramirez 05:32:21 08/01/03 You know I meant cars that are almost done:-) (n/m) - George(boost-solutions.com) 00:41:14 08/01/03 shop choice - WhiteOutZ 20:52:20 07/31/03 Please read the entire thread: - Bryan (AKA B-Ster) 20:55:11 07/31/03 That thread was 2 weeks ago...where are the pictures???????? (n/m) - Kyle(Houston) 21:03:53 07/31/03 When I have the opportunity to take the time to get>> - Bryan (AKA B-Ster) 22:11:14 07/31/03 B, I got the springs in:-) Do not ask me how, esp on the - George(boost-solutions.com) 00:45:33 08/01/03 Well done! (n/m) - Bryan (AKA B-Ster) 09:45:10 08/01/03 Great....I am waiting to see the results so we can put---> - Kyle(Houston) 06:50:20 08/01/03 How do you get exact clearance specs on toasted - MikeH(Twin GT35BB Incon Z) 09:53:04 08/01/03 Why not have the a reputable machine shop do it directly - MikeH(Twin GT35BB Incon Z) 21:49:47 07/31/03 Did you take yours back to the same machine shop???---> - Kyle(Houston) 06:53:07 08/01/03 Nope, I didn't, been 3 years, What's your point? (n/m) - MikeH(Twin GT35BB Incon Z) 09:49:38 08/01/03 I sense a little hostility in your tone? - MikeH(Twin GT35BB Incon Z) 12:30:39 08/01/03 At least my engine lasted much longer than Bryan's - MikeH(Twin GT35BB Incon Z) 12:51:03 08/01/03 Thanks...you finally answered the question.... (n/m) - Kyle(Houston) 13:58:00 08/01/03 Why not just wire me the funds and be done with it? (n/m) - BryZ32TT 22:46:26 07/31/03 You bought a civic? ;) (n/m) - BooZTT (Hawaii) 00:52:07 08/01/03 I hope everything works out for you. Just remember, it's - dilo 05:43:13 08/01/03 Damn, is that me posting under a different screen name?? - Bryan (AKA B-Ster) 09:47:31 08/01/03
Post a Followup	You cannot reply to this message because you are not logged in.