Subject	damn Pete sorry.
Posted by	Sweet Z(UTAH) on July 15, 2003 at 4:20 PM
	This message has been viewed 51 times.
In Reply To	Bad results guys. Sorry posted by TwinTurboPete on July 15, 2003 at 01:10 PM
Message	how was the curve?, It could be a boost leak if it was pushing out a lot of black smoke, cause with mass airs it they are reading all that air and the motor is not getting it, it will be running way rich. Also at the same time it could be the waste gate springs. We just had this prob. with A Z a lot of people are waiting on here, the wastegate was open the whole time and could only boost to 1.05 bar and the curve was way late. As for the dyno it should be fine and the O2 you can usually tell even though if you were shooting smoke and it was reading 12./1 which in my opinion is way lean for that low of boost then, I don't know? good luck and if you need anymore advise just ask? later, Danny RIP
Follow Ups	Bad results guys. Sorry - TwinTurboPete 13:10:53 07/15/03 dynojets never need recalibration, - Chris(NJ) 13:18:38 07/15/03 Damn. - ZHOUND 13:25:30 07/15/03 whenever you wanna check your O2s or compression, I'll help (n/m) - ZEngineer 13:45:29 07/15/03 Sorry to hear, BTW those samples went out today. (n/m) - aspendog 13:48:56 07/15/03 Re: Bad results guys. Sorry - sparkie 14:06:09 07/15/03 I agree, we have been seeing lots of "soft springs" - Z-king 14:47:45 07/15/03 ditto. that has been a lot of ppls problems with - Halo Z 15:04:15 07/15/03 I have 1.4 bar springs - TwinTurboPete 16:41:38 07/15/03 Old dyno make me think of this = Zeke's - Oppaman Z 14:16:53 07/15/03 Please tell me more (n/m) - TwinTurboPete 16:39:59 07/15/03 Give me a call during the day tomorrow please (n/m) - Oppaman Z 19:23:17 07/15/03 The source of the problem can be found here.. - AshsZ of Z1Motorsports.com 15:49:12 07/15/03 Wow, that is a great write up Ash. (n/m) - Z from Japan 22:29:39 07/15/03 damn Pete sorry. - Sweet Z(UTAH) 16:20:41 07/15/03 I have 1.4 bar springs :) (n/m) - TwinTurboPete 16:38:47 07/15/03 gotcha pete, it prob. isn't that but what I ment was? - Sweet Z(UTAH) 19:24:06 07/15/03 I am probably stupid or something - FANTAZ(Power Supply Racing) 17:14:47 07/15/03 more than most everyone on this forum.... (n/m) - LedZep(Rims for sale) 17:42:23 07/15/03 2nd. (n/m) - YugoBernie (NoVA) 18:21:55 07/15/03 8th (n/m) - Chris(NJ) 18:55:21 07/15/03 2+ bar of boost is plain old crazy to achieve 6xxwhp. - TwinTurboPete 01:23:18 07/16/03 Ouch Pete. Seems like the boost is going somewhere!??! (n/m) - Bryan (AKA B-Ster) 19:05:44 07/15/03 From 1.4bar to 1.7 bar netted me only 10whp or so - TwinTurboPete 01:24:23 07/16/03 did you record the dyno? Did you hear any break up? - Carlos Ramirez 20:03:40 07/15/03 I changed the plugs yesterday and there - TwinTurboPete 01:27:22 07/16/03 A car over here with twin 20G's did 580rwps at 1 bar. - Z from Japan 22:28:22 07/15/03 My car is not stroked and have a 7:8:1 compression - TwinTurboPete 01:29:07 07/16/03 Black smoke? Injector messed up? (n/m) - teahead 23:53:30 07/15/03 Please explain. We also noticed the - TwinTurboPete 01:31:25 07/16/03 Right side turbo flows to the left motor and then goes to .. - Ed(Toronto) 13:58:57 07/16/03
Post a Followup	You cannot reply to this message because you are not logged in.