Subject	NE1 familiar with custom woodworking (Ashley dear.. :) >>
Posted by	Bobby12many on June 30, 2003 at 2:02 AM
	This message has been viewed 77 times.
Message	WOuld it be reasonably easy for a qualified wood-worker(woodsmith?) to make a copy of the OEM shift knob made out of wood? If possible, what would a rough cost be? (just to fab the knob, no thread install, paint, coating, etc... TIA The "witcho" incident: "fuck you bitch you fuckin started this shit . say sorry or bring down your slow as z witcho slow as pops in the car and i'll teach you both a new lesson. Not internet related but PAIN related" ....posted by z32pilot on April 09, 2003 at 11:30 PM My sounddomain page Leave some feedback on my site!
Follow Ups	NE1 familiar with custom woodworking (Ashley dear.. :) >> - Bobby12many 02:02:32 06/30/03 it would be a bitch to make, here's why: - ZEngineer 02:07:53 06/30/03 Truth (n/m) - therinL 09:07:05 06/30/03 Put block of wood on lathe get basic size then dremel - RT 09:19:33 06/30/03 shouldn't be to hard for someone with lathe skills. - Spee 08:04:52 06/30/03 errr, did you read my reply...n00b? - ZEngineer 08:42:39 06/30/03 My dad is a TV repair man.... - zxtaz 09:01:34 06/30/03 Your kidding right? (n/m) - therinL 09:06:22 06/30/03 *sigh* - Dallas DamonZ 09:16:23 06/30/03 Wha? (n/m) - therinL 09:22:49 06/30/03 Fast Times at Ridgemont High. Go rent the DVD. (n/m) - SeedyROM 12:48:29 06/30/03 his what? (n/m) - Spee 10:16:10 06/30/03 ROFL... - boileralum 10:15:34 06/30/03 you can start with a couple of different axis points - kayoz 09:08:30 06/30/03 notice I said someone with lathe skills. - Spee 10:14:15 06/30/03 My reasons: - Bobby12many 12:48:36 06/30/03 Can you powdercoat wood? I'm pretty sure you need to - boileralum 13:03:52 06/30/03 Probably not. - Bobby12many 13:12:11 06/30/03 hehe... - Spee 13:18:41 06/30/03 wonder why he wants to paint it black ;) (n/m) - Kez43 14:22:03 06/30/03 black is beautiful :) (n/m) - Spee 16:06:26 06/30/03 Any decent woodworker with lathe (n/m) - RT 09:18:04 06/30/03 It would be easy no lathe needed. Band saw is about all you - kingtut(So.Cal) 10:30:26 06/30/03 2nd, two hours labor tops. - ni[X]it 10:40:57 06/30/03 I was quoted $40 shipped for the final unfinished knob - Bobby12many 12:51:05 06/30/03 I think my glass eye looks cool. (n/m) - kingtut(So.Cal) 13:03:06 06/30/03 My buddy can make one for the right $$ - he carves - BummedOutMonkey(Ztard) 12:03:49 06/30/03 Sorry that your monkey is bummed out. :( . (n/m) - ni[X]it 13:29:20 06/30/03 Not too hard to do. - AshsZ (FabZEM All) 15:51:30 06/30/03
Post a Followup	You cannot reply to this message because you are not logged in.