Subject	What about the vacuum line running on the upper part of the
Posted by	KaZ (VaBch) on June 05, 2003 at 2:09 PM
	This message has been viewed 29 times.
In Reply To	If you trace out the galley you will see it goes to the posted by Keith58 on June 05, 2003 at 12:22 PM
Message	Galley? When I removed my EGR and AIV functionality I removed the galley... I've since run that fitting to the Throttle Body... is that an error in flow? Or should I just plug both? Just curious what everyone thinks... KaZ (VaBch) - "Unique Z" Dyno'd - 335 RWHP / 361 RWTQ @ 15 TDC / 17 PSI AIM - KaZsMiR / E-mail @ Hotmail - casimijg
Follow Ups	one step forward, two steps back (hardpipe install) - fourZero 10:52:49 06/05/03 on a side note, the hardpipes look good :-P (n/m) - Pure-Evil 11:03:36 06/05/03 another pic of the pipes... - fourZero 11:08:44 06/05/03 ever thought about cutting an inch or so off them screws? - ZBlacktt 11:20:49 06/05/03 yeah, I'm gonna trim the bolts down later today.. (n/m) - fourZero 11:21:48 06/05/03 closeup of the nub, just for you! - fourZero 11:40:14 06/05/03 No, now ;) - ZBlacktt 11:46:23 06/05/03 you're blind... - fourZero 11:49:49 06/05/03 Anybody else see his picture? lol. Well. - ZBlacktt 12:14:06 06/05/03 I hope you're 100% sure on this, bro - fourZero 16:12:14 06/05/03 easy, trace the line, a.v.i infront, egr in back, - ZBlacktt 16:31:01 06/05/03 are these Ash's hardpipes? if so, did you find the drivers - Pure-Evil 11:24:35 06/05/03 yes, AshSpec aluminized pipes - fourZero 11:29:26 06/05/03 i did it with a hacksaw by hand...tiring for sure (n/m) - Pure-Evil 12:33:19 06/05/03 I like 'em =) - KILLR300ZX 13:46:26 06/05/03 Looks nice Four Zero! your one up on us! lol!!!!!! (n/m) - lewoolf2 20:21:35 06/05/03 man, I just finished capping that hole and installing pipes - fourZero 21:43:03 06/05/03 Not that hard to take the whole duct off and get a used one. (n/m) - Woody75 (Denver) 11:08:21 06/05/03 maybe so, but I haven't driven the car in 3 weeks - fourZero 11:10:26 06/05/03 Is there enough room to install HKS BOV's on your pipes? (n/m) - aliaZ 11:19:35 06/05/03 of course.. look @ Ash's setup - fourZero 11:22:44 06/05/03 But you don't want to put them there. - MugenRacer 11:26:11 06/05/03 true, you do want them close to the TBs.. - fourZero 11:27:44 06/05/03 If you trace out the galley you will see it goes to the - Keith58 12:22:03 06/05/03 What about the vacuum line running on the upper part of the - KaZ (VaBch) 14:09:12 06/05/03 So far the vote is 2 for AIV, 1 for EGR. Which is it? (n/m) - fourZero 14:27:36 06/05/03 I do believe that goes to the AIV... - John(Houston) 14:07:18 06/05/03 thanks for the insight! - fourZero 14:27:06 06/05/03 gator wrench =D (n/m) - PhRoZeN 16:54:31 06/05/03
Post a Followup	You cannot reply to this message because you are not logged in.