Subject	I like 'em =)
Posted by	KILLR300ZX on June 05, 2003 at 1:46 PM
	This message has been viewed 14 times.
In Reply To	another pic of the pipes... posted by fourZero on June 05, 2003 at 11:08 AM
Message	a lot softer on the eyes than the bling bling mirror-polish ones that ALWAYS stand out b/c the rest of th engine bay is dull.....these are sorta subtle, nice pipes. "I have a bike when I want to go fast, and a Z for when I want to go faster."-ZHOUND
Follow Ups	one step forward, two steps back (hardpipe install) - fourZero 10:52:49 06/05/03 on a side note, the hardpipes look good :-P (n/m) - Pure-Evil 11:03:36 06/05/03 another pic of the pipes... - fourZero 11:08:44 06/05/03 ever thought about cutting an inch or so off them screws? - ZBlacktt 11:20:49 06/05/03 yeah, I'm gonna trim the bolts down later today.. (n/m) - fourZero 11:21:48 06/05/03 closeup of the nub, just for you! - fourZero 11:40:14 06/05/03 No, now ;) - ZBlacktt 11:46:23 06/05/03 you're blind... - fourZero 11:49:49 06/05/03 Anybody else see his picture? lol. Well. - ZBlacktt 12:14:06 06/05/03 I hope you're 100% sure on this, bro - fourZero 16:12:14 06/05/03 easy, trace the line, a.v.i infront, egr in back, - ZBlacktt 16:31:01 06/05/03 are these Ash's hardpipes? if so, did you find the drivers - Pure-Evil 11:24:35 06/05/03 yes, AshSpec aluminized pipes - fourZero 11:29:26 06/05/03 i did it with a hacksaw by hand...tiring for sure (n/m) - Pure-Evil 12:33:19 06/05/03 I like 'em =) - KILLR300ZX 13:46:26 06/05/03 Looks nice Four Zero! your one up on us! lol!!!!!! (n/m) - lewoolf2 20:21:35 06/05/03 man, I just finished capping that hole and installing pipes - fourZero 21:43:03 06/05/03 Not that hard to take the whole duct off and get a used one. (n/m) - Woody75 (Denver) 11:08:21 06/05/03 maybe so, but I haven't driven the car in 3 weeks - fourZero 11:10:26 06/05/03 Is there enough room to install HKS BOV's on your pipes? (n/m) - aliaZ 11:19:35 06/05/03 of course.. look @ Ash's setup - fourZero 11:22:44 06/05/03 But you don't want to put them there. - MugenRacer 11:26:11 06/05/03 true, you do want them close to the TBs.. - fourZero 11:27:44 06/05/03 If you trace out the galley you will see it goes to the - Keith58 12:22:03 06/05/03 What about the vacuum line running on the upper part of the - KaZ (VaBch) 14:09:12 06/05/03 So far the vote is 2 for AIV, 1 for EGR. Which is it? (n/m) - fourZero 14:27:36 06/05/03 I do believe that goes to the AIV... - John(Houston) 14:07:18 06/05/03 thanks for the insight! - fourZero 14:27:06 06/05/03 gator wrench =D (n/m) - PhRoZeN 16:54:31 06/05/03
Post a Followup	You cannot reply to this message because you are not logged in.