Subject	Take a long steel pipe..
Posted by	fantomZ on June 03, 2003 at 2:08 PM
	This message has been viewed 42 times.
In Reply To	How in the world do u get these damned lug nuts off posted by bassplayr on June 03, 2003 at 02:05 PM
Message	and put it on the end of a 1/2in drive breaker bar and pry down on it. It should give you a lot more torque, but if they are stuck on that tight, you may break off the stud, which is not good. If you have an impact, thats the best way to do it
Follow Ups	How in the world do u get these damned lug nuts off - bassplayr 14:05:36 06/03/03 turn left not right, spee. (n/m) - Halo Z 14:07:34 06/03/03 gee, thanks ;) (n/m) - bassplayr 14:10:33 06/03/03 :*( (n/m) - Spee 16:03:09 06/03/03 At his size, I would stay on his good side :c) - sebring1970 (robo) 22:44:56 06/03/03 i have a LB or 30 on him. - Halo Z 14:05:46 06/04/03 but you're only 5'7" ;c) (n/m) - sebring1970 (robo) 17:54:56 06/04/03 little bit taller than that. haha (n/m) - Halo Z 19:12:44 06/04/03 Yes, but I also lift and am a young strapping man at 19 ;) (n/m) - bassplayr 22:05:56 06/04/03 Alls I know is that I want both you guys on my side :c) (n/m) - sebring1970 (robo) 00:28:09 06/05/03 i lift too. just 12 and 24 ozs. =\ (n/m) - Halo Z 14:31:34 06/05/03 Re: How in the world do u get these damned lug nuts off - SactoTodd 14:08:24 06/03/03 Well, it was worth a shot. A small one though (n/m) - bassplayr 14:11:52 06/03/03 Re: Re: How in the world do u get these damned lug nuts off - zxtaz 14:46:50 06/03/03 Knock'er Loose, WD-40, any good penetrating oil. - MugenRacer 14:08:27 06/03/03 Take a long steel pipe.. - fantomZ 14:08:54 06/03/03 Might just go to the import shop and use the air wrench (n/m) - bassplayr 14:11:23 06/03/03 agree...about 3-4' pipe should do the trick. (n/m) - Escort Z 14:12:04 06/03/03 Force*distance is your lever arm... this is the way to do it (n/m) - Scotts94z32 16:28:53 06/03/03 counter -clockwise to loose, clockwise to tighten. (n/m) - MikeH(Twin GT35BB Incon Z) 14:14:20 06/03/03 Re: counter -clockwise to loose, clockwise to tighten. - whitetwinz 17:12:19 06/03/03 Use a torque wrench...and if you don't have one... - Black Mammoth (VA) 14:17:56 06/03/03 shouldn't use a torque wrench as a breaker bar (n/m) - Ron(HouTX) 14:27:39 06/03/03 I'm sure that they aren't stuck. I'm sure that they are... - Black Mammoth (VA) 14:37:47 06/03/03 Yeah I need my own tools - bassplayr 19:29:45 06/03/03 2nd (n/m) - aliaZ 14:38:28 06/03/03 You need to check - D-JAY 14:30:47 06/03/03 D-jay, love the H*R in the sig!!! (n/m) - fantomZ 14:37:46 06/03/03 Nope, car feels great - bassplayr 19:30:59 06/03/03 That's just a warm up. Caliper bolts are worse> - John P. 14:42:59 06/03/03 1/2 drive rachet with deep well socket - EricTTZ 15:02:12 06/03/03 i used the handle from my jack to extend the wrench arm... (n/m) - hypo 16:08:09 06/03/03 Oh man, once you get your lug nuts torqued down - sebring1970 (robo) 18:13:11 06/03/03 Tell me about it - bassplayr 22:20:02 06/03/03 That's scary. Don't break your wheel studs. Good luck. (n/m) - sebring1970 (robo) 22:39:32 06/03/03
Post a Followup	You cannot reply to this message because you are not logged in.