Subject	I agree, a competant shop should have checked if there
Posted by	MikeH(Twin GT35BB Incon Z) on June 01, 2003 at 1:33 PM
	This message has been viewed 63 times.
In Reply To	recently there has been some issue with simply because of posted by Carlos Ramirez on June 01, 2003 at 01:26 PM
Message	was an offset instead of assume they are centered. So with coatings you want run tighter. Instead of .003 clearance for uncoated , something like .002 for coated. Mike
Follow Ups	Does anyone have a solution to the Weisco Piston problem? - aliaZ 10:45:20 06/01/03 The offset is suppose to go in opposite direction - MikeH(Twin GT35BB Incon Z) 10:49:29 06/01/03 ok...got it backwards (n/m) - aliaZ 11:10:52 06/01/03 yo i got wiseco pistons also - cuervokid 10:53:39 06/01/03 did they come with instructions? There is suppose - MikeH(Twin GT35BB Incon Z) 11:09:53 06/01/03 you'd have to measure it - aliaZ 11:10:14 06/01/03 I have a stock piston I am going to measure to see - MikeH(Twin GT35BB Incon Z) 11:30:54 06/01/03 Nope - there is an offset - SteamyZ(ZtoyZ.NET) 21:37:29 06/01/03 You are right the stock piston does have an offset - MikeH(Twin GT35BB Incon Z) 12:42:35 06/01/03 Re: Does anyone have a solution to the Weisco Piston problem? - VECTOR 12:54:39 06/01/03 When you measure clearance to cylinder wall is it - MikeH(Twin GT35BB Incon Z) 13:06:46 06/01/03 that is right you run tighter.. (n/m) - Carlos Ramirez 13:24:15 06/01/03 Funny Thing: Wiseco recomends .003" EVEN with COATED - VECTOR 14:08:06 06/01/03 I like to hear SGP's stance on the Wiseco. (n/m) - MikeH(Twin GT35BB Incon Z) 13:11:08 06/01/03 recently there has been some issue with simply because of - Carlos Ramirez 13:26:28 06/01/03 I agree, a competant shop should have checked if there - MikeH(Twin GT35BB Incon Z) 13:33:08 06/01/03 Agreed. Heard Wiseco's slap horrendously when installed - AshsZ (FabZEM All) 14:01:32 06/01/03 Who's "WE"? Z1 have had "bad luck" with Wisecos >>> - VECTOR 14:12:46 06/01/03 Wiseco didn't specify what end went where - excessive - AshsZ (FabZEM All) 14:37:02 06/01/03 I agree Wiseco should have marked their pistons - MikeH(Twin GT35BB Incon Z) 15:05:37 06/01/03 CP Pistons are suppose to be the best in the market - Carlos Ramirez 15:12:15 06/01/03 You saying offset creates more friction? I called - MikeH(Twin GT35BB Incon Z) 15:23:48 06/01/03 yes. more offset = more friction - aliaZ 16:47:13 06/01/03 The problem has been corrected now - SteamyZ(ZtoyZ.NET) 20:13:53 06/01/03 good to hear (n/m) - aliaZ 20:56:56 06/01/03
Post a Followup	You cannot reply to this message because you are not logged in.