Subject	recently there has been some issue with simply because of
Posted by	Carlos Ramirez on June 01, 2003 at 1:26 PM
	This message has been viewed 67 times.
In Reply To	Does anyone have a solution to the Weisco Piston problem? posted by aliaZ on June 01, 2003 at 10:45 AM
Message	of the offset pins and the fact that they didn't mentioned it anywhere in the documentation. A few motors that are out there were built with the pistons and they made the following mistakes 1) The measured the piston and then added to much clearance. 2) The pistons where installed backwards and some had some clatter. The problem is therefore simple make sure you have them installed forwards and run tighter specs.
Follow Ups	Does anyone have a solution to the Weisco Piston problem? - aliaZ 10:45:20 06/01/03 The offset is suppose to go in opposite direction - MikeH(Twin GT35BB Incon Z) 10:49:29 06/01/03 ok...got it backwards (n/m) - aliaZ 11:10:52 06/01/03 yo i got wiseco pistons also - cuervokid 10:53:39 06/01/03 did they come with instructions? There is suppose - MikeH(Twin GT35BB Incon Z) 11:09:53 06/01/03 you'd have to measure it - aliaZ 11:10:14 06/01/03 I have a stock piston I am going to measure to see - MikeH(Twin GT35BB Incon Z) 11:30:54 06/01/03 Nope - there is an offset - SteamyZ(ZtoyZ.NET) 21:37:29 06/01/03 You are right the stock piston does have an offset - MikeH(Twin GT35BB Incon Z) 12:42:35 06/01/03 Re: Does anyone have a solution to the Weisco Piston problem? - VECTOR 12:54:39 06/01/03 When you measure clearance to cylinder wall is it - MikeH(Twin GT35BB Incon Z) 13:06:46 06/01/03 that is right you run tighter.. (n/m) - Carlos Ramirez 13:24:15 06/01/03 Funny Thing: Wiseco recomends .003" EVEN with COATED - VECTOR 14:08:06 06/01/03 I like to hear SGP's stance on the Wiseco. (n/m) - MikeH(Twin GT35BB Incon Z) 13:11:08 06/01/03 recently there has been some issue with simply because of - Carlos Ramirez 13:26:28 06/01/03 I agree, a competant shop should have checked if there - MikeH(Twin GT35BB Incon Z) 13:33:08 06/01/03 Agreed. Heard Wiseco's slap horrendously when installed - AshsZ (FabZEM All) 14:01:32 06/01/03 Who's "WE"? Z1 have had "bad luck" with Wisecos >>> - VECTOR 14:12:46 06/01/03 Wiseco didn't specify what end went where - excessive - AshsZ (FabZEM All) 14:37:02 06/01/03 I agree Wiseco should have marked their pistons - MikeH(Twin GT35BB Incon Z) 15:05:37 06/01/03 CP Pistons are suppose to be the best in the market - Carlos Ramirez 15:12:15 06/01/03 You saying offset creates more friction? I called - MikeH(Twin GT35BB Incon Z) 15:23:48 06/01/03 yes. more offset = more friction - aliaZ 16:47:13 06/01/03 The problem has been corrected now - SteamyZ(ZtoyZ.NET) 20:13:53 06/01/03 good to hear (n/m) - aliaZ 20:56:56 06/01/03
Post a Followup	You cannot reply to this message because you are not logged in.