Subject	$$ mainly for my time, I will charge a lot for a one-off
Posted by	Chip(GinnMotorsports) on March 18, 2003 at 10:51 PM
	This message has been viewed 30 times.
In Reply To	And what would $$ be... For Rotor, adapt. & balancer? (n/m) posted by garth8934(Seattle) on March 18, 2003 at 10:27 PM
Message	custom kit. If it were something that I could sell many of, the labor could be amortized over many sets, but in this case one set would be stuck with labor, machining etc. You would REALLY have to make it worth my time, I am working on other things that have a much higher demand, and I am only a one man show.
Follow Ups	Why doesn't anybody sell rear brake kits? >>> - NytWolf 16:39:55 03/18/03 I think 80% of braking is from front brake. - LVS 16:42:38 03/18/03 Coz sells rear big brakes I believe - U ZCREAM 16:45:12 03/18/03 Luv my new bad azzz brakes - MACHZ 17:01:24 03/18/03 those brakes are awesome. And Russell is a good guy. (n/m) - Guapo 17:13:01 03/18/03 2nd (n/m) - Spee 17:30:59 03/18/03 What are you shopping for? Nice looking or performance? - YugoBernie (NoVA) 16:50:41 03/18/03 Man have I witnessed that before - U ZCREAM 16:56:02 03/18/03 Looking for >>> - NytWolf 17:13:17 03/18/03 Doesn't sounds like performance to me - Kamaitachi (Dokuzetsu) 17:18:08 03/18/03 Errr ... maybe I'm after looks then (n/m) - NytWolf 17:21:25 03/18/03 Didn't think this out too well, did ya? (n/m) - Spee 17:42:23 03/18/03 Read my response to YugoBernie (n/m) - NytWolf 17:51:10 03/18/03 You have a lot to learn about brakes. (n/m) - YugoBernie (NoVA) 17:19:26 03/18/03 Where did you get your brakes from? (n/m) - NytWolf 17:27:11 03/18/03 Bernie has Stoptechs. X-drilled OR slotted, not both (n/m) - Scotts94z32 17:29:03 03/18/03 Read my first post. (n/m) - YugoBernie (NoVA) 17:30:33 03/18/03 I did. (n/m) - NytWolf 17:31:43 03/18/03 It answers your question. (n/m) - YugoBernie (NoVA) 17:34:06 03/18/03 Let me start over -->>> - NytWolf 17:49:31 03/18/03 I hope you are ready to spend about $5k for your cosmetic - Scotts94z32 18:00:23 03/18/03 Finally, someone who understands what I'm after >>> - NytWolf 18:49:50 03/18/03 Sure, 1) = AP Racing 6-Piston kit - Kamaitachi (Dokuzetsu) 18:01:25 03/18/03 Have you tracked your AP kit with HARD braking? - Scotts94z32 18:14:37 03/18/03 Glenn has the setup, never any problems. That is the best>> - Zster (QuickZilver) 19:13:43 03/18/03 Look at this page for a few more inexpensive upgrades - Chip(GinnMotorsports) 18:08:27 03/18/03 GamblerZs kit is nice. and its dirt cheap. (n/m) - fairladyz90999 16:53:44 03/18/03 Stoptech has a rear kit, but not too many ppl have it - Scotts94z32 17:27:45 03/18/03 Currently ST does not have a rear kit for a 300ZX. (n/m) - YugoBernie (NoVA) 17:33:18 03/18/03 Bernie - read: - Scotts94z32 17:43:53 03/18/03 You are right, they don't, but, they DO build one for the - ScreemZ 18:39:27 03/18/03 umm but new fronts, move old fronts to the rears. Duh. - Halo Z 18:11:31 03/18/03 I brought this up once before - U ZCREAM 19:25:26 03/18/03 hmmm (n/m) - Halo Z 19:33:00 03/18/03 If you do it you will need some massive front calipers - Chip(GinnMotorsports) 19:53:28 03/18/03 i would think so sense the fronts are 4 pot and the rear are - Halo Z 20:03:32 03/18/03 Honestly, if you really wanted a good track setup this is a - Chip(GinnMotorsports) 21:01:33 03/18/03 What for !? - PLEAZURE in CA (SD) 18:24:30 03/18/03 If you guys really want one, I can get StopTech to make them - Coz@CZP 18:53:03 03/18/03 You should probably make a new post for all to see about - Scotts94z32 18:59:21 03/18/03 I'm gonna talk to ST, and then i'll post something :) (n/m) - Coz@CZP 19:21:52 03/18/03 I've asked this quest. b4... Couldn't someone come up - garth8934(Seattle) 22:05:29 03/18/03 I will do it if the $$ is right. (n/m) - Chip(GinnMotorsports) 22:23:42 03/18/03 And what would $$ be... For Rotor, adapt. & balancer? (n/m) - garth8934(Seattle) 22:27:51 03/18/03 Or beter yet as an add on to a front kit? (n/m) - garth8934(Seattle) 22:33:57 03/18/03 $$ mainly for my time, I will charge a lot for a one-off - Chip(GinnMotorsports) 22:51:05 03/18/03 Anyone else interested?????? (n/m) - garth8934(Seattle) 22:56:20 03/18/03 I believe KVR performance can make you the kit you want... - Goose93 21:16:56 03/18/03 Russell(Dallas) has the Wilwoods for all 4 corners>> - Dallas DamonZ 23:48:32 03/18/03
Post a Followup	You cannot reply to this message because you are not logged in.