Subject	After reading all the posts, I'm left with one thought..
Posted by	-Ever- on March 18, 2003 at 6:11 PM
	This message has been viewed 26 times.
In Reply To	Is it more feasable to put a water mist injection before or posted by Milo (San Antonio, TX.) on March 18, 2003 at 10:17 AM
Message	Why not spray before the IC's as well as close to the TB's? I've never set up an aquamist system before so I'm not sure if there would be any limiting factor as to why you couldn't spray in two locations of the same path of air travel. The only thing I could think of is that you would be limited to the amount of water injected overall and injecting in one prime location could be more efficient (just how much...?) than spraying a lesser amount in two. 272rwhp 258rwt If it's not broken, lets take it apart and find out why not.
Follow Ups	Is it more feasable to put a water mist injection before or - Milo (San Antonio, TX.) 10:17:09 03/18/03 FWIW; Aquamist GB is on permanent hold. - niXit 10:25:19 03/18/03 Thanx for the FYI, nixit. (n/m) - Milo (San Antonio, TX.) 10:28:53 03/18/03 Its gonna be specific to the vehicle. - AshsZ (FabZEM All) 11:03:07 03/18/03 Thermodynamic transfer rate is higher as the difference - AshsZ (FabZEM All) 10:54:20 03/18/03 SEE, that is the way I was thinking (ie- injection right - Milo (San Antonio, TX.) 11:31:54 03/18/03 Re: Thermodynamic transfer rate is higher as the difference - niXit 11:59:36 03/18/03 Devil's Advocate: You will decrease the flow through - Chip(GinnMotorsports) 12:34:21 03/18/03 But the hot water will transfer more of the heat to - AshsZ (FabZEM All) 14:18:29 03/18/03 So you think that more than makes up for the restriction? - Chip(GinnMotorsports) 15:22:59 03/18/03 If I had a thermo book handy, I would model the system - BigTDogg (BOOST-GASM!!!!!) 13:11:45 03/18/03 RE: analysis, - niXit 13:45:00 03/18/03 Agree 100% - RSR 13:54:54 03/18/03 True, and like Nixit said, there are many unknowns.. - BigTDogg (BOOST-GASM!!!!!) 14:06:36 03/18/03 However, that info could be easily collected with the - AshsZ (FabZEM All) 14:23:47 03/18/03 I have 16 channels of A-D I could employ to do this. - AshsZ (FabZEM All) 14:22:07 03/18/03 Question for you about aquamist testing - Chip(GinnMotorsports) 15:25:44 03/18/03 Empirical testing hands Sir. Theory his arse. :) (n/m) - AshsZ (FabZEM All) 14:24:31 03/18/03 I would be worried about the water falling - RSR 13:20:25 03/18/03 My biggest concern would be the corrosion of the IC's. - AshsZ (FabZEM All) 14:26:23 03/18/03 Good point. (n/m) - Milo (San Antonio, TX.) 15:14:47 03/18/03 After reading all the posts, I'm left with one thought.. - -Ever- 18:11:50 03/18/03
Post a Followup	You cannot reply to this message because you are not logged in.