Subject	Captain Obvious may ring in on this, and it does seem
Posted by	AshsZ (FABio) on March 14, 2003 at 2:32 PM
	This message has been viewed 63 times.
In Reply To	this may be too obvious, but posted by Marshall on March 14, 2003 at 02:25 PM
Message	obvious, but Im just trying to get an idea of the distance between the stock caliper and the i.d. of these wheels, or even with a ~325-330mm rotor and stock caliper. It would also be really nice to know what the gap is between the back of the spokes and the caliper face (where the nissan logo is) so I can determine if I'm going to have the clearance I need. I didn't have to use spacers with the Momo's to get it to clear the caliper in the front, but there was a little over 3/8" clearance between the stock caliper location and the back of the Momo's spokes so the brake upgrade (cobra rotors) fit with enough slack. These Blitz wheels have this polished lip which leads me to believe that the spokes are recessed deeper into the wheel, which will put the back of the spokes closer to the caliper face. :-/ Just wanting a picture to see so I can start making preparations for a new brake system. I can't return the wheels at this point. [ ashleypowers.com ] [ agpowers@bellsouth.net ] [ Zemulator Information Sheet ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast?
Follow Ups	Need some help, hope someone has a pic. >>> - AshsZ (FABio) 14:06:38 03/14/03 Bah, Type 03s are overrated! - boileralum00 14:14:14 03/14/03 Compare the offsets, how much difference? Don't believe the - Milo (San Antonio, TX.) 14:16:04 03/14/03 What is the clearance between the back of the 'spokes' - AshsZ (FABio) 14:19:47 03/14/03 this may be too obvious, but - Marshall 14:25:56 03/14/03 Captain Obvious may ring in on this, and it does seem - AshsZ (FABio) 14:32:38 03/14/03 I dunno how relevant it is, but on my 18s there isn't a - boileralum00 14:48:54 03/14/03 That inner ridge where the center attaches to the wheel - AshsZ (FABio) 14:53:25 03/14/03 Yes, mine are 18". I'd think you could sell the 17s fairly - boileralum00 14:59:05 03/14/03 If you could get a measurement of the gap between the - AshsZ (FABio) 15:09:59 03/14/03 I'll make some measurements for you tomorrow when I go - boileralum00 15:48:18 03/14/03 Much appreciated bro! (n/m) - AshsZ (FabZEM All) 20:55:10 03/14/03 Blitz does not make a 17X9 that clears STOCK brakes - Chip(GinnMotorsports) 15:37:48 03/14/03 Interesting. What has to be done to make them fit? (n/m) - AshsZ (FABio) 15:51:42 03/14/03 Big spacer, they are not a high disk design. (n/m) - Chip(GinnMotorsports) 09:43:33 03/15/03 im sure they will fit, i have 13 inch rotors on my car with - gtclk 16:40:02 03/14/03 His problem is very odd offset because of custom rotors. (n/m) - YugoBernie (NoVA) 09:40:44 03/15/03 Why didn't U get 18x9s? At any rate, 03s sweet upgrade - teahead 21:15:24 03/14/03
Post a Followup	You cannot reply to this message because you are not logged in.