Subject	Load on the rod bearing (and rods) goes up exponentially
Posted by	Chip(GinnMotorsports) on February 28, 2003 at 1:56 PM
	This message has been viewed 180 times.
In Reply To	Can't over-revving kill bearings too? posted by Kez43 on February 28, 2003 at 11:52 AM
Message	with RPM, seems like it is to the 2nd power.
Follow Ups	Who makes the best Rod Bearing? - Jeff K. 23:15:04 02/27/03 Which one did you "cook" (n/m) - ImTheDevil 23:16:27 02/27/03 Re: Which one did you "cook" - Jeff K. 23:18:40 02/27/03 I have been told that the "best" rod bearing >> - Mal1ce 23:37:45 02/27/03 Clevite bearings or the stock ones. It really doesnt matter - Good2Zya 00:57:43 02/28/03 P.S. Dont use the Z31 bearing. Like Mallce said... - Good2Zya 01:08:25 02/28/03 Z31 engines last a long time though - Marshall 12:11:48 02/28/03 Its interesting tho, the Z31 bearings are highly >>> - Zster (QuickZilver) 13:20:42 02/28/03 It wasn't detonation or oil contamination - Jeff K. 01:29:16 02/28/03 Well a good machineist will be able 2 tell U what happened (n/m) - Good2Zya 01:34:32 02/28/03 I will have it out and apart in a couple of weeks. I hope!! (n/m) - Jeff K. 01:42:14 02/28/03 Two other possibilities - Good2Zya 01:52:04 02/28/03 I think you are right on the bearing seat. - Jeff K. 02:02:17 02/28/03 Can't over-revving kill bearings too? - Kez43 11:52:52 02/28/03 Load on the rod bearing (and rods) goes up exponentially - Chip(GinnMotorsports) 13:56:39 02/28/03 ACL or Clevite bearings with Black F1 coatings - Carlos Ramirez 06:22:34 02/28/03 would that be titanium nitride coating? (n/m) - Chris-TTZ 07:09:19 02/28/03 don't remember right now I have to look it up again. (n/m) - Carlos Ramirez 07:54:46 02/28/03 no biggie. just curious. (n/m) - Chris-TTZ 08:02:19 02/28/03 2nd (n/m) - Z1 Motorsports 18:30:26 02/28/03 388RWHP@406TQ. I use stock bearings. Keep in mind >>>> - AshsZ (FABio) 08:24:05 02/28/03 540RWHP@481TQ..I use Clevite bearings (n/m) - Good2Zya 09:40:19 02/28/03 What is the benefits of those over stock? - AshsZ (FABio) 12:07:04 02/28/03 I doubt there is any. In fact the stock ones I think - Good2Zya 12:34:29 02/28/03 That is a good point! AshsZ - Jeff K. 14:18:52 02/28/03 I use stock in mine . They are the best according to - MikeH(Twin GT35BB Incon Z) 10:02:39 02/28/03 Stock bearings. - ZHOUND 13:05:31 02/28/03
Post a Followup	You cannot reply to this message because you are not logged in.