Subject	Two other possibilities
Posted by	Good2Zya on February 28, 2003 at 1:52 AM
	This message has been viewed 165 times.
In Reply To	I will have it out and apart in a couple of weeks. I hope!! (n/m) posted by Jeff K. on February 28, 2003 at 01:42 AM
Message	There is a very small oil galley in each journal. One, or more may have gotten cloged. Or, the bearing seat may have given way causing the bearing to be spun. Fred 95 300TT SGP Stage..Who knows..lol Dynoed 539.4 RWHP, 481.2 Lbs. Torque Pump Gas @ 17 Lbs. of Boost NO NOS!!
Follow Ups	Who makes the best Rod Bearing? - Jeff K. 23:15:04 02/27/03 Which one did you "cook" (n/m) - ImTheDevil 23:16:27 02/27/03 Re: Which one did you "cook" - Jeff K. 23:18:40 02/27/03 I have been told that the "best" rod bearing >> - Mal1ce 23:37:45 02/27/03 Clevite bearings or the stock ones. It really doesnt matter - Good2Zya 00:57:43 02/28/03 P.S. Dont use the Z31 bearing. Like Mallce said... - Good2Zya 01:08:25 02/28/03 Z31 engines last a long time though - Marshall 12:11:48 02/28/03 Its interesting tho, the Z31 bearings are highly >>> - Zster (QuickZilver) 13:20:42 02/28/03 It wasn't detonation or oil contamination - Jeff K. 01:29:16 02/28/03 Well a good machineist will be able 2 tell U what happened (n/m) - Good2Zya 01:34:32 02/28/03 I will have it out and apart in a couple of weeks. I hope!! (n/m) - Jeff K. 01:42:14 02/28/03 Two other possibilities - Good2Zya 01:52:04 02/28/03 I think you are right on the bearing seat. - Jeff K. 02:02:17 02/28/03 Can't over-revving kill bearings too? - Kez43 11:52:52 02/28/03 Load on the rod bearing (and rods) goes up exponentially - Chip(GinnMotorsports) 13:56:39 02/28/03 ACL or Clevite bearings with Black F1 coatings - Carlos Ramirez 06:22:34 02/28/03 would that be titanium nitride coating? (n/m) - Chris-TTZ 07:09:19 02/28/03 don't remember right now I have to look it up again. (n/m) - Carlos Ramirez 07:54:46 02/28/03 no biggie. just curious. (n/m) - Chris-TTZ 08:02:19 02/28/03 2nd (n/m) - Z1 Motorsports 18:30:26 02/28/03 388RWHP@406TQ. I use stock bearings. Keep in mind >>>> - AshsZ (FABio) 08:24:05 02/28/03 540RWHP@481TQ..I use Clevite bearings (n/m) - Good2Zya 09:40:19 02/28/03 What is the benefits of those over stock? - AshsZ (FABio) 12:07:04 02/28/03 I doubt there is any. In fact the stock ones I think - Good2Zya 12:34:29 02/28/03 That is a good point! AshsZ - Jeff K. 14:18:52 02/28/03 I use stock in mine . They are the best according to - MikeH(Twin GT35BB Incon Z) 10:02:39 02/28/03 Stock bearings. - ZHOUND 13:05:31 02/28/03
Post a Followup	You cannot reply to this message because you are not logged in.