Subject	A few questions...
Posted by	BeanZ on December 26, 2002 at 9:33 PM
	This message has been viewed 40 times.
In Reply To	PE1820 compressor map (as requested) posted by Chip(GinnMotorsports) on December 26, 2002 at 04:45 PM
Message	How much do these bad boys cost? How's the lag? Do they bolt right on without any problems? Thanks
Follow Ups	PE1820 compressor map (as requested) - Chip(GinnMotorsports) 16:45:03 12/26/02 Wow, bro can you explain some of that....lol. :) (n/m) - ZBlacktt 16:51:45 12/26/02 In a nutshell, 18m^3 choke flow at ~15 psi - Chip(GinnMotorsports) 18:42:42 12/26/02 um....is that good? (n/m) - Zboost 16:56:49 12/26/02 is that 79% ? that's the most efficient ive seen (n/m) - Jefe 17:34:05 12/26/02 Yes, 79% max efficiency. (n/m) - Chip(GinnMotorsports) 18:31:20 12/26/02 ok ppl think of it as a releafe(SP) map, the "high" - Halo Z 17:43:30 12/26/02 relief map (n/m) - stupidfast [ ///M Power ] 21:29:01 12/26/02 hey what happened to the one that was on a paper napkin? - Carlos Ramirez 18:06:38 12/26/02 http://www.gnttype.org/techarea/turbo/turboflow.html (n/m) - Carlos Ramirez 18:07:02 12/26/02 3.5 bar is 50 psi, they will not do that, sorry. - Chip(GinnMotorsports) 18:35:48 12/26/02 Considering you sell the kit, wouldn't it be in your best - SeedyROM 19:03:29 12/26/02 My reply to ZBlackTT was a basic, but good rundown. (n/m) - Chip(GinnMotorsports) 19:11:18 12/26/02 Just saw that, cool - SeedyROM 20:15:20 12/26/02 you have to remember that the compressor map - Carlos Ramirez 19:15:21 12/26/02 That is not bar, it is pressure ratio - Chip(GinnMotorsports) 19:36:24 12/26/02 Its the same thing bro do the simple math :-) - Carlos Ramirez 19:41:49 12/26/02 The point was that 28 is the most that you want to try to - Chip(GinnMotorsports) 19:53:33 12/26/02 That map only goes up to 2 bar (n/m) - U ZCREAM (TTZ in '03) 19:51:36 12/26/02 hey chip... - Altersys 18:41:22 12/26/02 You want to stay away from the surge line - Chip(GinnMotorsports) 18:46:13 12/26/02 is this what happens to our stock turbos at 17+ psi? - Altersys 19:05:55 12/26/02 No, surge line is always the lowest possible airflow - Chip(GinnMotorsports) 19:09:47 12/26/02 Hmmm, you should read it again then - U ZCREAM (TTZ in '03) 19:52:40 12/26/02 A few questions... - BeanZ 21:33:48 12/26/02 $4000 for the bolt-on kit, gaskets lines, etc. - Chip(GinnMotorsports) 22:32:51 12/26/02 And both trims of PE turbos have water-cooled jackets? - U ZCREAM (TTZ in '03) 23:03:07 12/26/02 All are watercooled. Thay are IHI turbos - Chip(GinnMotorsports) 09:14:02 12/27/02 can you post the 1420 map ? (n/m) - Chris(NJ) 09:39:05 12/27/02
Post a Followup	You cannot reply to this message because you are not logged in.