Subject	I should have flow data on EH manifolds in a week or so >>
Posted by	Mal1ce on November 12, 2002 at 11:34 AM
	This message has been viewed 59 times.
In Reply To	Extrude hone exhaust manifolds, really worth the $500? posted by Turbodog (CT) on November 12, 2002 at 09:54 AM
Message	I'll be comparing extrude honed, hand ported, and stock manifolds in addition to some aftermarket units. I'll post all the data as we get it. ============================================================================   erikboehringer: but i like big gay cock erikboehringer: i cant be a good ol boy Mal1ce666: uhhhh.......well, too bad Mal1ce666: fake it..... Mal1ce666: you do know how to fake it .....right? erikboehringer: only if i am slapped the right way
Follow Ups	Extrude hone exhaust manifolds, really worth the $500? - Turbodog (CT) 09:54:00 11/12/02 In the same situation---> - Miles (San Antonio, TX) 10:10:04 11/12/02 not beating a dead horse but>>> - SL103 10:38:11 11/12/02 That is why I don't sell that service. (n/m) - Miles (San Antonio, TX) 11:15:44 11/12/02 Um, according to extrudehone.com it's almost $1200.oo - niXit 10:53:03 11/12/02 Well...... that sucks. (n/m) - Miles (San Antonio, TX) 11:16:18 11/12/02 Where do you see that? - Turbodog (CT) 11:18:06 11/12/02 I called last week, they told me 500$ (n/m) - Hungryjack 11:28:33 11/12/02 I thought it was $500 for each manifold? - Marshall 13:20:38 11/12/02 They said for both. They said it didn't matter what - Hungryjack 14:43:49 11/12/02 I called 6 months ago and was told 550(?) for each (n/m) - niXit 10:10:19 11/13/02 I should have flow data on EH manifolds in a week or so >> - Mal1ce 11:34:26 11/12/02 Thanx, Mallice. (n/m) - Miles (San Antonio, TX) 12:25:07 11/12/02 can that be a sticky for a couple days so nobody misses it? (n/m) - Chris(NJ) 17:33:43 11/12/02 They R in da same league with Stealin and Microsoft=Monopoly (n/m) - Arturo C. 11:45:55 11/12/02 I call them extrudeWhore, they are a monopoly (n/m) - MikeH(Twin GT35BB Incon Z) 12:46:09 11/12/02 I had mine done and really didn't see much difference - MikeH(Twin GT35BB Incon Z) 12:45:23 11/12/02 It should be more than just polished, shouldn't it? - Marshall 13:19:30 11/12/02 yes, it should make the inside diameter bigger (n/m) - Jefe 13:22:33 11/12/02 Exactly what I needed to hear, just to clarify --> - Turbodog (CT) 13:31:36 11/12/02 Re: Exactly what I needed to hear, just to clarify --> - MikeH(Twin GT35BB Incon Z) 14:09:27 11/12/02 Thank you much sir! - Turbodog (CT) 14:31:38 11/12/02 Greg had his done. I made boost 500rpm earlier with porting. - xybertron 00:47:34 11/13/02
Post a Followup	You cannot reply to this message because you are not logged in.