Subject	I wonder if those overclockers are assuming the CPU
Posted by	AshsZ (The Rebuild King) on November 08, 2002 at 1:57 PM
	This message has been viewed 52 times.
In Reply To	:/ posted by LegoZ_81 on November 08, 2002 at 01:36 PM
Message	is perfectly flat.... I dont see them lapping it to the CPU's crown.. Lapping is the mating of surfaces.. dictionary.com demonstrates this term: Lapping: To hone (two mating parts) against each other until closely fitted.. The best way to do this would be to use lapping compound between the sink and the crown and some sort of tool to gyrate one of the parts. [ ashleypowers.com ] [ agpowers@bellsouth.net ] When pigs dance, you better get it on video... "You never really learn to swear until you learn to drive." -George Carlin
Follow Ups	For those considering "SL103" for porting...more pics - GamblerZ 10:37:58 11/08/02 A few comments about Shawn's work.-> - Miles (San Antonio, TX) 10:51:54 11/08/02 I'm having problems too!Where are my 4.0TB's its been 4 mont - gc91ttz 11:00:41 11/08/02 HUH? Did you ship these to me or Shawn? I never recieved - Miles (San Antonio, TX) 11:10:58 11/08/02 If you need some work, for you I'll do yours at a - Miles (San Antonio, TX) 11:13:37 11/08/02 No, I sent them to Shawn. I shelled out $575 - gc91ttz 11:18:45 11/08/02 OUCH.... sorry. He is in directory (call him) - Miles (San Antonio, TX) 11:24:45 11/08/02 Man that just plain sucks A$$! (n/m) - TARGETZ 11:11:11 11/08/02 Note- Myself & Antonio do some very good work. - Miles (San Antonio, TX) 11:20:04 11/08/02 what are your prices? (n/m) - CaptanZap 11:24:12 11/08/02 RE- Prices? - Miles (San Antonio, TX) 11:51:42 11/08/02 Not commenting in general about other's performance - GamblerZ 11:40:27 11/08/02 Sorry, Gambler. But thanx for reply. (n/m) - Miles (San Antonio, TX) 11:55:59 11/08/02 Very True, Sorry to hear you got ripped. (n/m) - SniPer SR71 (Dallas) 18:36:45 11/08/02 Yea I'm just blown away... - Adam A. 11:48:41 11/08/02 True dat. I'm shocked as well. (n/m) - Miles (San Antonio, TX) 11:57:12 11/08/02 Adam - SL103 19:20:31 11/08/02 I'm not the only one having problems with SL103 - GamblerZ 20:34:17 11/08/02 I would like to hear what Shawn has to say? (n/m) - MikeH(Twin GT35BB Incon Z) 12:36:54 11/08/02 I contacted him 10/31 and have yet to hear from him - GamblerZ 15:38:57 11/08/02 You are not suppose to gasket match unless you do the - MikeH(Twin GT35BB Incon Z) 12:43:28 11/08/02 Gambler sent him the lower plenum for that exact reason (n/m) - Mal1ce 12:51:43 11/08/02 Correct otherwise you just got a big wall to slow - Miles (San Antonio, TX) 13:54:42 11/08/02 If he had both plenums, where's the problem? (n/m) - GamblerZ 14:09:31 11/08/02 Honestly, he should have just done them if that's what was - Miles (San Antonio, TX) 14:14:09 11/08/02 Ok, try again. Here's what its supposed to look like :) - AshsZ (The Rebuild King) 13:03:53 11/08/02 :/ - LegoZ_81 13:36:09 11/08/02 I wonder if those overclockers are assuming the CPU - AshsZ (The Rebuild King) 13:57:19 11/08/02 Re: I wonder if those overclockers are assuming the CPU - LegoZ_81 14:29:44 11/08/02 I'm not putting any blame on anyone, I was just curious - AshsZ (The Rebuild King) 14:55:39 11/08/02 Well said. (n/m) - Miles (San Antonio, TX) 16:21:52 11/08/02 Damn!! Do the valves really open that much? (n/m) - mongoozTT 14:10:26 11/08/02 No, there aren't any springs on those. :) - AshsZ (The Rebuild King) 14:15:10 11/08/02 hey Re re read next time its port matching - SL103 19:16:08 11/08/02 You should stop embarrassing yourself... - GamblerZ 20:30:15 11/08/02 Gambler Z is RIGHT!!!I had work by sL103 and it was shit! (n/m) - ZleppyZ 21:12:23 11/08/02 Re: hey Re re read next time its port matching - gc91ttz 23:17:28 11/08/02
Post a Followup	You cannot reply to this message because you are not logged in.