Subject	No, I sent them to Shawn. I shelled out $575
Posted by	gc91ttz on November 08, 2002 at 11:18 AM
	This message has been viewed 67 times.
In Reply To	HUH? Did you ship these to me or Shawn? I never recieved posted by Miles (San Antonio, TX) on November 08, 2002 at 11:10 AM
Message	: anything from you. Beside I only port out 1.5mm at the most to utilize the stock butterfly. It gives a good punch of horsepower at a fraction of the cost. I do these port & polished for about $125 for both. (cleaning included) If I only knew about you!!!
Follow Ups	For those considering "SL103" for porting...more pics - GamblerZ 10:37:58 11/08/02 A few comments about Shawn's work.-> - Miles (San Antonio, TX) 10:51:54 11/08/02 I'm having problems too!Where are my 4.0TB's its been 4 mont - gc91ttz 11:00:41 11/08/02 HUH? Did you ship these to me or Shawn? I never recieved - Miles (San Antonio, TX) 11:10:58 11/08/02 If you need some work, for you I'll do yours at a - Miles (San Antonio, TX) 11:13:37 11/08/02 No, I sent them to Shawn. I shelled out $575 - gc91ttz 11:18:45 11/08/02 OUCH.... sorry. He is in directory (call him) - Miles (San Antonio, TX) 11:24:45 11/08/02 Man that just plain sucks A$$! (n/m) - TARGETZ 11:11:11 11/08/02 Note- Myself & Antonio do some very good work. - Miles (San Antonio, TX) 11:20:04 11/08/02 what are your prices? (n/m) - CaptanZap 11:24:12 11/08/02 RE- Prices? - Miles (San Antonio, TX) 11:51:42 11/08/02 Not commenting in general about other's performance - GamblerZ 11:40:27 11/08/02 Sorry, Gambler. But thanx for reply. (n/m) - Miles (San Antonio, TX) 11:55:59 11/08/02 Very True, Sorry to hear you got ripped. (n/m) - SniPer SR71 (Dallas) 18:36:45 11/08/02 Yea I'm just blown away... - Adam A. 11:48:41 11/08/02 True dat. I'm shocked as well. (n/m) - Miles (San Antonio, TX) 11:57:12 11/08/02 Adam - SL103 19:20:31 11/08/02 I'm not the only one having problems with SL103 - GamblerZ 20:34:17 11/08/02 I would like to hear what Shawn has to say? (n/m) - MikeH(Twin GT35BB Incon Z) 12:36:54 11/08/02 I contacted him 10/31 and have yet to hear from him - GamblerZ 15:38:57 11/08/02 You are not suppose to gasket match unless you do the - MikeH(Twin GT35BB Incon Z) 12:43:28 11/08/02 Gambler sent him the lower plenum for that exact reason (n/m) - Mal1ce 12:51:43 11/08/02 Correct otherwise you just got a big wall to slow - Miles (San Antonio, TX) 13:54:42 11/08/02 If he had both plenums, where's the problem? (n/m) - GamblerZ 14:09:31 11/08/02 Honestly, he should have just done them if that's what was - Miles (San Antonio, TX) 14:14:09 11/08/02 Ok, try again. Here's what its supposed to look like :) - AshsZ (The Rebuild King) 13:03:53 11/08/02 :/ - LegoZ_81 13:36:09 11/08/02 I wonder if those overclockers are assuming the CPU - AshsZ (The Rebuild King) 13:57:19 11/08/02 Re: I wonder if those overclockers are assuming the CPU - LegoZ_81 14:29:44 11/08/02 I'm not putting any blame on anyone, I was just curious - AshsZ (The Rebuild King) 14:55:39 11/08/02 Well said. (n/m) - Miles (San Antonio, TX) 16:21:52 11/08/02 Damn!! Do the valves really open that much? (n/m) - mongoozTT 14:10:26 11/08/02 No, there aren't any springs on those. :) - AshsZ (The Rebuild King) 14:15:10 11/08/02 hey Re re read next time its port matching - SL103 19:16:08 11/08/02 You should stop embarrassing yourself... - GamblerZ 20:30:15 11/08/02 Gambler Z is RIGHT!!!I had work by sL103 and it was shit! (n/m) - ZleppyZ 21:12:23 11/08/02 Re: hey Re re read next time its port matching - gc91ttz 23:17:28 11/08/02
Post a Followup	You cannot reply to this message because you are not logged in.