Subject	I wouldn't worry about it Kuah >>>
Posted by	KaZ (jTTfz) NoVa on August 01, 2002 at 8:37 AM
	This message has been viewed 46 times.
In Reply To	Sadly, the cost of the 8 industrial bearings alone > posted by kZtt (zedparts.com) on July 31, 2002 at 01:03 PM
Message	I think with the quality your talking on your product, and them being in the $500-$600 range, versus $800-$900 for a comparible product, you'll have no problems selling them. I for one won't buy anyone's slip box design... no matter how good they say it is... Later, KaZ KaZ (jspec Twin Turbo fairlady z) Northern Virginia - "Unique Z" Dyno'd - 339 RWHP / 369 RWTQ @ 17 TDC AIM - KaZsMiR / E-mail @ Hotmail - casimijg 17 Timing Belts, 5 Suspension Installs, 4 Engine Pulls, 3 Clutch Installs, 2 Rear Mains, 1 Pop Charger and Counting...
Follow Ups	$295 - PAIR of Front Adj. Arms Group buy. Do you know - z ya 05:35:32 07/31/02 that's UAS's upper a-arm in their pic - Jjzx 05:56:21 07/31/02 I will have adjustable a-arms available soon, F&R, >> - AshsZ (Fab Whore, Ph.D) 07:10:04 07/31/02 Ash can you design the Hicas eliminator. The Stillen - MikeH(Twin GT35BB Incon Z) 11:56:37 07/31/02 I'm sure it could be done inexpensively. - AshsZ (Fab Whore, Ph.D) 12:12:03 07/31/02 I am still waiting on the ones that one of the other - aZiator 07:20:54 07/31/02 If you are patient, - rodelb 08:15:35 07/31/02 Nice work and timing... (n/m) - Goose93 08:25:32 07/31/02 I can't make out how you would adjust the front from the pic (n/m) - z ya 08:39:29 07/31/02 It is adjusted by turning the buckle in the center > - kZtt (zedparts.com) 09:34:30 07/31/02 Oh Ok. I thought it might be threaded. Wasn't clear in pic. - z ya 09:37:32 07/31/02 Exactly what I have been waiting for. Let me know when they - aZiator 09:14:12 07/31/02 We don't want competitive...we want cheaper :) (n/m) - wesman [92TT-less ] 09:30:44 07/31/02 You get what you pay for... (n/m) - Goose93 10:07:06 07/31/02 That would be true for a well established product. - z ya 10:56:14 07/31/02 The slip-box design is notoriously unreliable > - kZtt (zedparts.com) 11:29:06 07/31/02 All I have to say is: Dude your awsome... (n/m) - Goose93 11:33:45 07/31/02 Yeah.. if he was a girl.. i'll do him. (n/m) - chivas 12:14:23 07/31/02 then screw competitive pricing.. kill the market by selling - chivas 11:36:26 07/31/02 We are trying to get the price down > - kZtt (zedparts.com) 12:00:53 07/31/02 $300 is too expensive. Make them for $150 and you're in. (n/m) - AshsZ (Fab Whore, Ph.D) 12:17:49 07/31/02 Sadly, the cost of the 8 industrial bearings alone > - kZtt (zedparts.com) 13:03:38 07/31/02 I wouldn't worry about it Kuah >>> - KaZ (jTTfz) NoVa 08:37:32 08/01/02 That's low $300s for the set I assume? (n/m) - z ya 12:27:50 07/31/02 Yup, for the front a-arm set (n/m) - kZtt (zedparts.com) 13:02:17 07/31/02 I am in the groupbuy, I believe everything will be fine - George(boostsolutionsinc.net) 12:39:24 07/31/02 I do like the midori design, but cha-chang. - AshsZ (Fab Whore, Ph.D) 12:20:49 07/31/02 All I can say is check out your design thoroughly first > - kZtt (zedparts.com) 13:01:40 07/31/02 from experience.... - ghoztt 13:51:34 07/31/02 Why? So you can store 3 sets in your garage instead of 1? (n/m) - LordZ 12:32:36 07/31/02 I suppose you want a $10 BJ also? (n/m) - Keith58(BOV's: good or bad?) 17:08:08 07/31/02 nah....those are free ;-) (n/m) - wesman [92TT-less ] 19:06:48 07/31/02 I hope they will be under $150 per set, else - AshsZ (Fab Whore, Ph.D) 12:16:22 07/31/02
Post a Followup	You cannot reply to this message because you are not logged in.