Subject	i get 10psi at about 4300.and i still have the 7200
Posted by	ForceFedIndustries on July 26, 2002 at 2:12 PM
	This message has been viewed 37 times.
In Reply To	he is a little les than 9:1 with a 1.4mm gasket probably posted by Carlos Ramirez on July 26, 2002 at 12:11 PM
Message	rev limit, for now. jwt is gonna make me a chip for the 555's for use with vpc instead of the dual pop, 7900 rev limit. it makes peak power at 7200rpm. so i am gonna raise it :) 418rwhp and 344 ft lbs @ 10psi and 93 octane fuel(BP gas too yuk) Force Fed Industries 2924 E.14th Ave. Columbus, Ohio 43219 614-372-0824 http://www.forcefedindustries.com
Follow Ups	At only 10psi and pump gas..... - ForceFedIndustries 08:47:16 07/26/02 For as much as you put in to it... it better perform ;)grats (n/m) - Flycaz (MLB, FL) 08:56:22 07/26/02 Nice. (n/m) - MugenRacer 08:58:58 07/26/02 10 psi... on a TT? Let's see the dyno... - Perffect 09:06:57 07/26/02 Why is it hard to believe I did 516rwhp at 16 psi - MikeH(Twin GT35BB Incon Z) 09:27:41 07/26/02 Wow... well stock is 9 PSI... I just didn't know.. - Perffect 09:34:13 07/26/02 removed restrictions, better fuel map+ 1 psi - HakenTT 09:39:27 07/26/02 lol, 10psi on Greddy TD-05s != 10 psi on stocker turbos (n/m) - HogZ 09:57:24 07/26/02 Mike am racing you with 5psi! - HakenTT 09:35:01 07/26/02 I'm putting down 195 HP at 0 psi... NA power! n/m - Perffect 09:35:15 07/26/02 Skeptic Newbie... look @ his profile. - Ken (Playin' with fire at A&M 09:37:31 07/26/02 9 to 1 comp. ratio, with 10psi possible 400hp - HakenTT 09:43:04 07/26/02 Now I understand ...n/m - Perffect 09:59:20 07/26/02 Get off my balls... I just wanted to see the dyno n/m - Perffect 09:57:49 07/26/02 bozo alert. - Carlos Ramirez 10:01:07 07/26/02 are you going to raise the boost? (n/m) - MikeH(Twin GT35BB Incon Z) 09:41:07 07/26/02 i am gonig to raise at about 1000 miles.mmmmmm 25psi (n/m) - ForceFedIndustries 10:02:23 07/26/02 Could you post dyno sheets when you run 25 psi? n/m - Perffect 10:07:28 07/26/02 Tony, tell us how the 9:1 compression spools up - Chip(GinnMotorsports) 11:12:40 07/26/02 he is a little les than 9:1 with a 1.4mm gasket probably - Carlos Ramirez 12:11:59 07/26/02 i get 10psi at about 4300.and i still have the 7200 - ForceFedIndustries 14:12:38 07/26/02 Just wait till it is broken-in, will spool faster, what is > - Chip(GinnMotorsports) 14:50:50 07/26/02 @ what rpm? (n/m) - Jefe 11:51:12 07/26/02
Post a Followup	You cannot reply to this message because you are not logged in.