Subject	Adjust the accellerator cable>>
Posted by	AshsZ (Fab Whore, Ph.D) on July 10, 2002 at 2:19 PM
	This message has been viewed 75 times.
In Reply To	is there a way to safely make the Z have 0 psi? posted by Furious(Houston) on July 10, 2002 at 01:59 PM
Message	So that they can't open the throttle any more than 5-10%. I'm not sure if there is enough room on the threads for that so you may need to put a block under the gas pedal itself and play with the length. Perhaps a large bolt in the bottom side of the block to adjust how far the pedal can be depressed. : I am gonna have to leave my Z at the body shop for 3 wks to a month and I was wondering if there was a way to make it so that if they took my Z out they couldn't have too much fun with it. : Aside from installing a boost controller and then hiding it so they don't find it - how can this be done? (or can it)? [ ashleypowers.com ] [ agpowers@bellsouth.net ] When pigs dance, you better get it on video...
Follow Ups	is there a way to safely make the Z have 0 psi? - Furious(Houston) 13:59:55 07/10/02 Disconnect the boost selenoid and take it with you? - YugoBernie (NoVA) 14:03:23 07/10/02 is that safe? and... about the shop - Furious(Houston) 14:19:52 07/10/02 No idea. Honestly your best move is to have them sign a - YugoBernie (NoVA) 14:51:02 07/10/02 Easy to get 7 psi safety boost, not sure about no boost (n/m) - RT 14:03:47 07/10/02 dont think so. - Francis (Houston) 14:06:46 07/10/02 no - BCs300z 14:12:30 07/10/02 good shops will take down milage before they begin (n/m) - zads 14:12:58 07/10/02 still going to dfw this weekend? (n/m) - LordZ 14:15:02 07/10/02 not this weekend - next (n/m) - Furious(Houston) 14:17:40 07/10/02 Adjust the accellerator cable>> - AshsZ (Fab Whore, Ph.D) 14:19:56 07/10/02 Search BigTDogg and Valet, I posed this question >>> - BigTDogg 14:29:12 07/10/02 how rough will the car run w/o MAS though? - Furious(Houston) 15:00:20 07/10/02 True, and I have no idea how to hook it up>>> - BigTDogg 15:04:18 07/10/02 Disconnect the wastegate actuators >>> - RickZ 14:56:01 07/10/02 that's what JohnY said too - seems like a lot of work though (n/m) - Furious(Houston) 15:00:50 07/10/02 Re: that's what JohnY said too - seems like a lot of work th - RickZ 15:15:24 07/10/02 wouldn't you only have to do one? (n/m) - Chris-TTZ 16:14:29 07/10/02 that would still make 7PSI (n/m) - BCs300z 15:06:56 07/10/02 I said wire the wastegates open full time = no boost (n/m) - RickZ 15:11:46 07/10/02 how bad would it be to just remove BOVs? - Furious(Houston) 15:02:09 07/10/02 Retard the ignition timing...>>> - Michael(Dallas) 15:03:48 07/10/02 Won't disconnecting mas limit it to 2500 rpm??? (n/m) - RT 15:25:23 07/10/02 won't that kill the car right when you touch the pedal? (n/m) - 3 double-0 ZX (Va Bch) 16:02:45 07/10/02 nope, mine putted around fine with the MAF disconnected (n/m) - Kez43 16:42:07 07/10/02 With out the MAF, the MF-er may not even start! - ELDIABLO 16:35:34 07/10/02 Disconnect your coolent temp sensor - cheezoto(now w/ ECU) 16:26:45 07/10/02 here's my thoughts though.... - Furious(Houston) 16:39:33 07/10/02 better than nothing - cheezoto(now w/ ECU) 19:19:48 07/10/02 Unplug the oil sending unit connector ;OÞ (n/m) - TRUOMEGA 18:01:07 07/10/02 Just set it at 7psi.... - socos 18:29:36 07/10/02 serously find another shop you can trust (n/m) - cheezoto(now w/ ECU) 19:21:12 07/10/02 install a Racelogic traction control system. :) - Bernie 21:19:55 07/10/02 Wire the wastegates open? (n/m) - MugenRacer 12:33:13 07/11/02
Post a Followup	You cannot reply to this message because you are not logged in.