Subject	is there a way to safely make the Z have 0 psi?
Posted by	Furious(Houston) on July 10, 2002 at 1:59 PM
	This message has been viewed 124 times.
Message	I am gonna have to leave my Z at the body shop for 3 wks to a month and I was wondering if there was a way to make it so that if they took my Z out they couldn't have too much fun with it. Aside from installing a boost controller and then hiding it so they don't find it - how can this be done? (or can it)? "And Shepherds we shall be, for Thee my Lord, for Thee. Power hath descended forth from Thy hand that our feet may swiftly carry out Thy command. We shall flow a river forth unto Thee And teeming with souls shall it ever be. In nomine Patris, et Fili, et Spiritu Sancti."
Follow Ups	is there a way to safely make the Z have 0 psi? - Furious(Houston) 13:59:55 07/10/02 Disconnect the boost selenoid and take it with you? - YugoBernie (NoVA) 14:03:23 07/10/02 is that safe? and... about the shop - Furious(Houston) 14:19:52 07/10/02 No idea. Honestly your best move is to have them sign a - YugoBernie (NoVA) 14:51:02 07/10/02 Easy to get 7 psi safety boost, not sure about no boost (n/m) - RT 14:03:47 07/10/02 dont think so. - Francis (Houston) 14:06:46 07/10/02 no - BCs300z 14:12:30 07/10/02 good shops will take down milage before they begin (n/m) - zads 14:12:58 07/10/02 still going to dfw this weekend? (n/m) - LordZ 14:15:02 07/10/02 not this weekend - next (n/m) - Furious(Houston) 14:17:40 07/10/02 Adjust the accellerator cable>> - AshsZ (Fab Whore, Ph.D) 14:19:56 07/10/02 Search BigTDogg and Valet, I posed this question >>> - BigTDogg 14:29:12 07/10/02 how rough will the car run w/o MAS though? - Furious(Houston) 15:00:20 07/10/02 True, and I have no idea how to hook it up>>> - BigTDogg 15:04:18 07/10/02 Disconnect the wastegate actuators >>> - RickZ 14:56:01 07/10/02 that's what JohnY said too - seems like a lot of work though (n/m) - Furious(Houston) 15:00:50 07/10/02 Re: that's what JohnY said too - seems like a lot of work th - RickZ 15:15:24 07/10/02 wouldn't you only have to do one? (n/m) - Chris-TTZ 16:14:29 07/10/02 that would still make 7PSI (n/m) - BCs300z 15:06:56 07/10/02 I said wire the wastegates open full time = no boost (n/m) - RickZ 15:11:46 07/10/02 how bad would it be to just remove BOVs? - Furious(Houston) 15:02:09 07/10/02 Retard the ignition timing...>>> - Michael(Dallas) 15:03:48 07/10/02 Won't disconnecting mas limit it to 2500 rpm??? (n/m) - RT 15:25:23 07/10/02 won't that kill the car right when you touch the pedal? (n/m) - 3 double-0 ZX (Va Bch) 16:02:45 07/10/02 nope, mine putted around fine with the MAF disconnected (n/m) - Kez43 16:42:07 07/10/02 With out the MAF, the MF-er may not even start! - ELDIABLO 16:35:34 07/10/02 Disconnect your coolent temp sensor - cheezoto(now w/ ECU) 16:26:45 07/10/02 here's my thoughts though.... - Furious(Houston) 16:39:33 07/10/02 better than nothing - cheezoto(now w/ ECU) 19:19:48 07/10/02 Unplug the oil sending unit connector ;OÞ (n/m) - TRUOMEGA 18:01:07 07/10/02 Just set it at 7psi.... - socos 18:29:36 07/10/02 serously find another shop you can trust (n/m) - cheezoto(now w/ ECU) 19:21:12 07/10/02 install a Racelogic traction control system. :) - Bernie 21:19:55 07/10/02 Wire the wastegates open? (n/m) - MugenRacer 12:33:13 07/11/02
Post a Followup	You cannot reply to this message because you are not logged in.