Subject	I'm looking at some Samco 90 degree elbows that
Posted by	boileralum00 on June 21, 2002 at 11:41 AM
	This message has been viewed 31 times.
In Reply To	You must be clair-voyant. I am working on drawings for that posted by AshsZ (Fab Whore, Ph.D) on June 21, 2002 at 08:13 AM
Message	transition from 76mm on one leg to 61mm on the other. The silicone should be both sturdy enough and provide enough flexibility to get the job done. Cost - $74 shipped from Cybercraft. Then I am going to get a second MAF sensor (is $150 too much for one?), and use the 2-in Add setting on my S-AFC. I already paid for a second POP charger ($65), so my total will still be a little under $300 for everything. Rule #1 - There's always a bastard!
Follow Ups	Groupbuy: Hardpipe "Kits" w/some DIY involved. >>> - AshsZ (Fab Whore, Ph.D) 01:23:36 06/21/02 im in! (n/m) - DRIZCOL 01:27:19 06/21/02 fab up an injen style n/a kit :) - down5hift 01:31:59 06/21/02 It can be done.I'll draw up thediagrams.Wannabe a guinea pig - AshsZ (Fab Whore, Ph.D) 01:35:11 06/21/02 sure (n/m) - down5hift 01:36:40 06/21/02 how big is the intake piping for n/a?..... 2.5 right? (n/m) - down5hift 01:37:22 06/21/02 yah. I have the NA stock pipes to use as reference. - AshsZ (Fab Whore, Ph.D) 01:38:54 06/21/02 so it'd just be around 32 dollars for the piping? (n/m) - down5hift 01:42:19 06/21/02 No, it is $16 per bend. The pipe comes with it. :) - AshsZ (Fab Whore, Ph.D) 06:54:56 06/21/02 Hey Ash, my car will be a guinea pig. If you can fabricate - SpeedyZX 11:25:39 06/21/02 BTW, I am making nothing off of this. Just a free Zervice2U! (n/m) - AshsZ (Fab Whore, Ph.D) 01:33:06 06/21/02 your such a nice guy :) (n/m) - down5hift 01:35:01 06/21/02 I'll have you all converted to "Fab Whores"!! - AshsZ (Fab Whore, Ph.D) 01:37:23 06/21/02 I'm well on my way Pics next week! :) - MugenRacer 03:04:06 06/21/02 Whatcha making (memory sucks) (n/m) - BigTDogg 07:25:53 06/21/02 Heheh. One home-made dual pop/dual MAF setup, on the way (n/m) - boileralum00 07:54:30 06/21/02 You must be clair-voyant. I am working on drawings for that - AshsZ (Fab Whore, Ph.D) 08:13:10 06/21/02 I'm looking at some Samco 90 degree elbows that - boileralum00 11:41:37 06/21/02 Can I get these in BAMBOO? (n/m) - YugoBernie (NoVA) @ZCon '02 01:50:59 06/21/02 i think teak would match your car better (n/m) - down5hift 01:52:54 06/21/02 His shoe size is bigger than his IQ, give him a break. (n/m) - AshsZ (Fab Whore, Ph.D) 08:00:17 06/21/02 pic's please, I am intrested, anything to save a buck (n/m) - dragonballz 07:06:09 06/21/02 Gheeze, sig's are useless. There's one in my sig file! >>> - AshsZ (Fab Whore, Ph.D) 08:09:22 06/21/02 I'll be making those also very soon. (n/m) - govaardz(Aruba) 07:30:04 06/21/02 so all we have to do is make the cuts? - Chris (NJ) 07:39:04 06/21/02 Exactly. And I have diagrams that show you where to cut. - AshsZ (Fab Whore, Ph.D) 08:02:12 06/21/02 ok, so im in, keep us posted (n/m) - Chris (NJ) 09:15:43 06/21/02 I would love them. Wow Ash, lots going on! (n/m) - Adam A. 07:45:25 06/21/02 twin turbo hardpipes 250shipped and no turbo hardpipe 150 - govaardz(Aruba) 07:46:14 06/21/02 Is this the new eposodes of D*I*C*K*? I should mash you. - AshsZ (Fab Whore, Ph.D) 07:59:42 06/21/02 I am sorry ASH.those were not my intentions.check e-mail>> (n/m) - govaardz(Aruba) 08:29:38 06/21/02 So less than 100 bucks for everything? I'm game. (n/m) - BigTDogg 07:51:03 06/21/02 Hey Ash, I sent you an email. Did you ever get it? - ShiftCTRL 08:47:36 06/21/02 I'm in. (n/m) - blaZe(Dallas) 08:54:34 06/21/02 Possible to just get the inner pipes? - safZ 09:09:44 06/21/02 Sounds awesome! I'm in! (n/m) - CowBoy--TT Conversion Underway 09:24:30 06/21/02
Post a Followup	You cannot reply to this message because you are not logged in.