Subject	Here's my dyno from last year since we are posting
Posted by	MikeH(Twin GT35BB Incon Z) on June 13, 2002 at 12:59 AM
	This message has been viewed 150 times.
In Reply To	Get some #s and pull it again :) (n/m) posted by Specialty-Z on June 13, 2002 at 12:15 AM
Message	First sheet was done at 16psi Second sheet was done at 18-19psi with the dam clutch slipping under boost. I will by dynoing under higher boot later on this year. Arizona'a most powerful 600HP 15 second Z More powerful than a stock TT , slower than an NA Dynoed 515 rwhp and 420 ft.lbs @ 16psi 89 degrees. 533 rwhp and 450 ft. lbs @19 psi and slipping clutch and heat soaked motor , 85 degrees.
Follow Ups	JWT sport 500,Specialty Z manifold and split downpipe dyno.. - Specialty-Z 23:35:01 06/12/02 That is where I hope to be in a few weeks... - GamblerZ 23:38:59 06/12/02 Very nice! Any before/after comparisons on the manifolds? - TTony 23:42:50 06/12/02 We put the sport 500's on at same time.... - Specialty-Z 23:53:01 06/12/02 I want to see the manifolds before you let them go (n/m) - GamblerZ 23:55:01 06/12/02 What would be the approximate lead time on them? (n/m) - TTony 00:03:31 06/13/02 I made some changes to the second set and I want to see - Specialty-Z 00:10:13 06/13/02 I'll be following this. If I go with PE1420's I'm getting - TTony 00:26:11 06/13/02 that has been the setup ive been dreamin about lately.. (n/m) - NIXTA TTZ 07:43:46 06/13/02 I will be the guinie pig.... ;) (n/m) - spotz 00:06:30 06/13/02 how much boost were you running? (n/m) - MikeH(Twin GT35BB Incon Z) 23:48:48 06/12/02 Spikes to 24 psi and drops down to about 17-18 psi (n/m) - Seb 23:51:45 06/12/02 It holds more on the street...The dyno dosn't load the... - Specialty-Z 23:56:49 06/12/02 Thanks for everything! (n/m) - Seb 00:01:18 06/13/02 My Plessure Seb! (n/m) - Specialty-Z 00:07:49 06/13/02 How much does a setup like this cost? - Samer 00:08:30 06/13/02 Wish you had those manifold before I put my engine back in (n/m) - MikeH(Twin GT35BB Incon Z) 00:12:23 06/13/02 Get some #s and pull it again :) (n/m) - Specialty-Z 00:15:15 06/13/02 Do u want me 2 post pics? (n/m) - Seb 00:26:15 06/13/02 Here's my dyno from last year since we are posting - MikeH(Twin GT35BB Incon Z) 00:59:00 06/13/02 very nice numbers! how much for the manifolds? (n/m) - Chris (NJ) 07:22:08 06/13/02 nice, 500 torque - got rice? 09:20:27 06/13/02 Very nice, guys! Now, when-> - Kevin (CA) 09:54:35 06/13/02
Post a Followup	You cannot reply to this message because you are not logged in.