Subject	If a FMIC is around $1k, I will go that route. (n/m)
Posted by	TTony on June 03, 2002 at 1:46 PM
	This message has been viewed 22 times.
In Reply To	NO FMIC will be anywhere near that price. posted by Chip(GinnMotorsports) on June 03, 2002 at 01:12 PM
Message
Follow Ups	? about intercoolers for in classifieds - zpeed 09:17:00 06/03/02 I think they were just fabricated recently, but they look - dragonballz 09:48:55 06/03/02 I *think* they were built to HKS IC specs (n/m) - sbsTT(MD) 10:31:49 06/03/02 that's what I got from his e-mail BUT 1 in = 2.54 cm. - PiotrC70 11:26:24 06/03/02 PiotrC70 and I calculated Stillen's = 280 cubic in.... - gunghoe9 11:04:25 06/03/02 Re: PiotrC70 and I calculated Stillen's = 280 cubic in.... - kZtt (zedparts.com) 11:16:52 06/03/02 That's what I calculated the dimentions to be of the UK IC's - PiotrC70 11:24:39 06/03/02 Those specs on the Stillen/HKS/Greddy are core sizes > - kZtt (zedparts.com) 11:29:14 06/03/02 Oh i/c.... hahah funny joke get it? - gunghoe9 11:35:02 06/03/02 Very punny :) - kZtt (zedparts.com) 11:45:58 06/03/02 That's what I was thinking...very well priced...>>> - gunghoe9 11:48:04 06/03/02 2nded (n/m) - dragonballz 11:49:56 06/03/02 Why do you need piping for a sidemount? (n/m) - Chip(GinnMotorsports) 12:01:51 06/03/02 Good point Chip..I knew hung out here for a reason.... - gunghoe9 12:15:45 06/03/02 OTOH, you need piping and connectors for a FMIC. (n/m) - Chip(GinnMotorsports) 13:03:13 06/03/02 They seem like a good deal BUT if you want an established - Chip(GinnMotorsports) 10:25:16 06/03/02 From the pics I've seen they look quality... - Mal1ce 10:56:36 06/03/02 So who here is going to order them or do we wait for - zpeed 12:30:27 06/03/02 I am seriously considering them, as is PiotrC70 i think. (n/m) - gunghoe9 12:33:03 06/03/02 If price is right, I would rather do the FMIC. (n/m) - TTony 12:49:06 06/03/02 NO FMIC will be anywhere near that price. - Chip(GinnMotorsports) 13:12:41 06/03/02 If a FMIC is around $1k, I will go that route. (n/m) - TTony 13:46:26 06/03/02 I will guess that would be impossible. (n/m) - Chip(GinnMotorsports) 14:18:42 06/03/02 those look taller than they are wider, opposite of Stillens (n/m) - MikeH(Twin GT35BB Incon Z) 13:22:11 06/03/02 That's what I noticed as well. (n/m) - Woody75 (Denver) 13:25:08 06/03/02 Stillens are must bigger than those. (n/m) - MikeH(Twin GT35BB Incon Z) 13:29:24 06/03/02 I've seen these before in a z in Austin - killer z 16:39:28 06/03/02
Post a Followup	You cannot reply to this message because you are not logged in.