Subject	Might look at clutch master and slave cylinders as well>>>
Posted by	JeffZTT (ATL) on April 17, 2002 at 10:29 AM
	This message has been viewed 22 times.
In Reply To	$4 part cost me $1,700!!! posted by JRachner on April 16, 2002 at 10:47 PM
Message	If they have not been replaced on your car, the increased clutch pressure will probably cause them to fail. Not hard to do with everything assembled, but (a) who wants to bleed the clutch again if you can avoid it and (b) much easier to do this work at home rather than your work parking lot. Ima slap you. (n/m) - Jackie Chan (RH2-SWEET!) 23:37:45 08/09/01 just on the ass please. (n/m) - HaloZ 23:44:19 08/09/01
Follow Ups	$4 part cost me $1,700!!! - JRachner 22:47:35 04/16/02 I've spent $1,200 and it's NOT FIXED. $3,000 just to test - SeedyRom (Not Fixed) 22:50:10 04/16/02 Sorry to hear it's still not runnin... - JRachner 22:53:26 04/16/02 Thanks :) Runs great, just not well enough for Texas - SeedyRom (Not Fixed) 22:57:03 04/16/02 P.S. What did the Nismo bushing run ya? - SeedyRom (Not Fixed) 22:54:12 04/16/02 $12 and change (n/m) - JRachner 22:58:15 04/16/02 How do you always end up with the strange problems?>> - mtbakesz 22:58:46 04/16/02 Tell your mom those are pretty flowers... - JRachner 23:13:47 04/16/02 After 24 years, I'm used to it. (n/m) - SeedyRom (Not Fixed) 23:53:41 04/16/02 What was the 3k on? Did you get a new head gasket? (n/m) - LedZep(196.8 RWHP) 23:07:18 04/16/02 Not yet, but I'll have to spend it just to "check" - SeedyRom (Not Fixed) 23:53:17 04/16/02 That does suck, well keep a bottle of prestone, and - LedZep(196.8 RWHP) 11:45:54 04/17/02 BTW, is that 3k for both heads? (n/m) - LedZep(196.8 RWHP) 12:33:14 04/17/02 Stop your whinning. I paid $5,000 and my z was still broken - Qwk Z 10:07:03 04/17/02 Doh! (n/m) - SeedyRom (Not Fixed) 11:29:39 04/17/02 I like the trees.... - Jared Todd (NR to SactoTodd) 22:50:22 04/16/02 Funny thing... - JRachner 22:56:46 04/16/02 Lol, oops - Jared Todd (NR to SactoTodd) 21:08:38 04/17/02 I just did the same thing. I changed my tranny seals while - 91NAZ32(speed kills) 23:41:35 04/16/02 2nd that, my rear one began leaking 3k after cluttch install (n/m) - z324u 00:00:22 04/17/02 get a new pivot bolt as well. Nismo if you can find it. - Bernie 09:02:18 04/17/02 Might look at clutch master and slave cylinders as well>>> - JeffZTT (ATL) 10:29:37 04/17/02 Welcome to the club. My pivot ball resulted in >$2,200! (n/m) - teahead 13:58:41 04/17/02 J Spec knob/Steamy Boots with red stitches (n/m) - PLEAZURE in CA (SD) 17:53:47 04/17/02
Post a Followup	You cannot reply to this message because you are not logged in.