Subject	Cant afford it BUT i have some other plans
Posted by	SteamyZ(ZtoyZ.NET©) on March 19, 2002 at 12:45 PM
	This message has been viewed 148 times.
In Reply To	Good luck bro. posted by ZHOUND on March 19, 2002 at 12:33 PM
Message	3.2 liters, mild head work, NO BS port stuff...like stock plenum and lower maifold. Basically NO frills...not JUNK! Stock cams with upgraded springs and giudes. Basically Im going to spend my money on strength and about 100 additional RWHP without NOS on these turbos. SHould go like this...tell me what you think...I need all the input I can get 3.2 liter punch - JE 90mm pistons - swaine coated Tubular manifolds Bigger AR on HKS 2530 turbos - extrude honed too - should flow 600 RWHP with added displacement Mild port and polish on head (same set-up as you basically) Peened and plished rods and cranks with balanced bottom end Direct port 150 shot (this is a frill i may not do yet) Looking for 700 RWHP HP on the NOS and 600 off Visit ZtoyZ.NET Check out my UPDATED site for : Shift Boots Interior Packages Seats and Trims T-Top Bags ZtoyZ related news and info WITH our new phone number 626-786-5197
Follow Ups	Well, compression #'s are in - SteamyZ(ZtoyZ.NET©) 12:16:30 03/19/02 what kind of compression tester did you use? (n/m) - my91z 12:25:33 03/19/02 A snap-on (n/m) - SteamyZ(ZtoyZ.NET©) 13:23:05 03/19/02 I meant physical type, not brand lol >>> - my91z 14:36:49 03/19/02 lol-oh....yea it was threaded - SteamyZ(ZtoyZ.NET©) 17:32:51 03/19/02 sounds like it's time to have some fun! (n/m) - felixx23 12:30:52 03/19/02 Good luck bro. - ZHOUND 12:33:09 03/19/02 Cant afford it BUT i have some other plans - SteamyZ(ZtoyZ.NET©) 12:45:45 03/19/02 I would get Eagle or Crower rods while you are down there - TwinTurboPete 12:57:01 03/19/02 Rods will be fine - SteamyZ(ZtoyZ.NET©) 13:19:44 03/19/02 Re: Cant afford it BUT i have some other plans - ZHOUND 13:08:24 03/19/02 You have a valid point for consideration - SteamyZ(ZtoyZ.NET©) 13:17:43 03/19/02 Re: You have a valid point for consideration - SactoTodd 13:26:02 03/19/02 hehehehehe ----she'll take it (n/m) - SteamyZ(ZtoyZ.NET©) 13:38:19 03/19/02 600rwhp on 555s doesnt sound like much fun for your engine (n/m) - Jefe 13:59:46 03/19/02 fpr! (n/m) - ZHOUND 16:27:29 03/19/02 Make sure you enlarge water passage near #6 piston. (n/m) - teahead 14:38:24 03/19/02 So what are your plans? How long is it gonna be down ? (n/m) - wesman [92TT-less ] 12:36:40 03/19/02 read my post to ZO...i THINK - SteamyZ(ZtoyZ.NET©) 12:54:03 03/19/02 Sorry to hear...good luck. (n/m) - RSR 12:37:09 03/19/02 funny how bad news is often really good news in disguise. - Bernie 12:41:16 03/19/02 I guess being optimistic is better :) (n/m) - timz 12:45:54 03/19/02 Its only good news IF a rebuild/new engine is in the budget. (n/m) - Z-Jay (Edmonton) 14:19:33 03/19/02 What lead to low compression in #6? Do you have EGT? - timz 12:44:47 03/19/02 I have no real clue to be honest - SteamyZ(ZtoyZ.NET©) 12:47:58 03/19/02 Yeah the reason I ask is because of the #6 :) - timz 12:55:05 03/19/02 OK will do - SteamyZ(ZtoyZ.NET©) 12:59:31 03/19/02 its almost eerie how often #6 is the problem.. - NIXTA TTZ 15:09:49 03/19/02 I melted #5 and my #6 was perfect (n/m) - CarlCuro (busted...again) 16:39:30 03/19/02 sig=hilarious (n/m) - joel(PA) 20:03:56 03/19/02 What was the final word on your turbos? - JRH(KY) 13:02:42 03/19/02 Dont know FOR SURE but they appear to be fine - SteamyZ(ZtoyZ.NET©) 13:21:55 03/19/02 You mean when I got the $^@(# scared out of me - Wild Z 14:11:42 03/19/02 LOL - yea it was down some power then... - SteamyZ(ZtoyZ.NET©) 17:31:39 03/19/02 NE1 wanna buy an NA in excellent condition? (n/m) - Wild Z 18:02:03 03/19/02
Post a Followup	You cannot reply to this message because you are not logged in.