Subject	half shafts dont use u joints the use CV joints (n/m)
Posted by	TARGETZ on March 16, 2002 at 12:52 PM
	This message has been viewed 21 times.
In Reply To	Thats a half shaft from what it looks like posted by SteamyZ(ZtoyZ.NET©) on March 16, 2002 at 12:19 PM
Message
Follow Ups	Powertrain alum. DS. Do they all vibrate?? - Z-RATED 10:48:31 03/16/02 I heard they dont offer the aluminum one anyomore?? - TARGETZ 11:09:21 03/16/02 only alum for tt's. (n/m) - Chris (NJ) 15:55:34 03/16/02 some do some don't...steel DS maybe safer. (n/m) - Quiki(bling x 2) 11:09:34 03/16/02 The truth revealed! - Carlos Ramirez 11:17:59 03/16/02 Where did u get it? (n/m) - Seb 11:25:07 03/16/02 the dude i ordered mine said it was due to bad cardboard. - HaloZ• 13:16:15 03/16/02 whatever (n/m) - aliaZ 13:48:05 03/16/02 whatever yourself, "Stock Juan", they use card board in the - HaloZ• 13:52:40 03/16/02 Re: whatever yourself, "Stock Juan", they use card board in - aliaZ 14:34:56 03/16/02 well i wasn't talking to you in the first place and - HaloZ• 11:56:17 03/17/02 this is a public forum not email - aliaZ 12:19:49 03/17/02 basicly im saying im talking to carlos not u. (n/m) - HaloZ• 17:14:18 03/17/02 Wrong. Totally wrong. But good try. (n/m) - timz 14:48:20 03/16/02 LOL! Halo please listen to this guy (n/m) - aliaZ 18:32:19 03/16/02 shit, that's what i was told when i called powertrain. - HaloZ• 12:06:36 03/17/02 I thought it was there to stop sound noise? - Marshall 16:51:35 03/16/02 That is correct sir :P (n/m) - timz 18:02:33 03/16/02 sound noise/ stablizing - HaloZ• 11:59:58 03/17/02 What's the weight diff. between stock, al, and the> - SirpriZ 11:57:47 03/16/02 Guessing by holding mine at the time...... - ZBlacktt 12:17:25 03/16/02 Powertrain dosent make a steel for the TT (n/m) - snoguitar(loser) 12:40:59 03/16/02 Yah, they said it was too difficult..... - Some Dude 15:47:45 03/16/02 Re: What's the weight diff. between stock, al, and the> - Altered BeaZTT 15:48:13 03/16/02 well i just weighed mine since its sitting right here - Chris (NJ) 16:14:25 03/16/02 I posted this the other day...... - ZBlacktt 11:59:30 03/16/02 Thats a half shaft from what it looks like - SteamyZ(ZtoyZ.NET©) 12:19:05 03/16/02 It is a 2-piece DS, you can see the CSB in pic 2. (n/m) - Chip(GinnMotorsports) 12:20:55 03/16/02 cool...saw the CSB but didnt see after - SteamyZ(ZtoyZ.NET©) 12:27:45 03/16/02 I took that picture of the Supra Driveshaft :) (n/m) - ZBlacktt 12:23:32 03/16/02 half shafts dont use u joints the use CV joints (n/m) - TARGETZ 12:52:01 03/16/02 'Albert'?? LMAO!! His name be 'Adam Alter' (n/m) - snoguitar(loser) 12:36:16 03/16/02 Yea,yea,,,lol ( old school ) you know what I mean,,,,,lol ;) (n/m) - ZBlacktt 12:39:42 03/16/02 Was going off, one cup of coffee and hang over, jack leg ;) (n/m) - ZBlacktt 12:40:31 03/16/02 about the Driveshaft breaking - Marshall 16:40:40 03/16/02 Then stick with what you have :) (n/m) - ZBlacktt 16:43:14 03/16/02 I may eventually get something stronger - Marshall 16:47:03 03/16/02 None will vibrate if it's the correct phase. (n/m) - teahead 13:14:32 03/16/02 How much torque can the Al DS handle? - Marshall 13:33:22 03/16/02 a little less than three times what your car puts out ;) (n/m) - ZBlacktt 16:45:49 03/16/02 Damn, that's pretty strong - Marshall 16:48:50 03/16/02 No really,,,,,lol 800ft/TQ :) (n/m) - ZBlacktt 17:33:37 03/16/02 Inland empire driveline-1-909-279-8026 - BarryGZX 14:09:39 03/16/02 mine seemed ok on the drive home last night. (n/m) - Chris (NJ) 15:52:21 03/16/02
Post a Followup	You cannot reply to this message because you are not logged in.