Subject	It isn't too accurate>>>
Posted by	safZ on February 04, 2002 at 5:32 PM
	This message has been viewed 45 times.
In Reply To	it's like a plasticy/claylike stuff that comes in strips >> posted by my91z on February 04, 2002 at 02:14 PM
Message	since it is basically plastic or clay, temp. and humidity affects it greatly (width, etc.). Plastigage should only be used to check if clearances are even and all the same. Use a micrometer to actually check the clearances, not plastigage. Soren Faaborg I don't know what the question is, but the answer is turbo.
Follow Ups	Shittiest story of the day. Engine Rebuild 101 - AshsZ (LUMBRJCK) 13:09:00 02/04/02 plastigauge is your friend - Diamond Don 13:16:09 02/04/02 no kidding. (n/m) - HaloZ² 13:58:26 02/04/02 someone explain this plastigauge thing to me please. (n/m) - Bernie 14:05:24 02/04/02 it's like a plasticy/claylike stuff that comes in strips >> - my91z 14:14:51 02/04/02 It isn't too accurate>>> - safZ 17:32:05 02/04/02 dayam...dealership should pay you somehow for that... - CaptanZap(OK 2 B NA) 13:16:33 02/04/02 well..that sux but AT LEAST now you know what it is... - Pure-Evil 13:16:55 02/04/02 damn i hope it goes better next time (n/m) - MBS103 13:18:04 02/04/02 The right bearings are on their way. This weekend it'll happ - AshsZ (LUMBRJCK) 13:21:56 02/04/02 if i was a little bit closer i would come down and help> - MBS103 13:31:00 02/04/02 Kinda sounds like you guys are in too much of a hurry to - JRH(KY) 13:22:12 02/04/02 LOL, He got a "note" from the apartment complex. >>> - AshsZ (LUMBRJCK) 13:23:59 02/04/02 He's late (n/m) - F8IZHIS 13:38:08 02/04/02 He put the exhaust on on the 30th, it was on the ground>> - AshsZ (LUMBRJCK) 14:03:12 02/04/02 lol (n/m) - F8IZHIS 14:08:06 02/04/02 my apts. would have thrown me out already, lol. They bitch > - my91z 13:43:02 02/04/02 ok, I got this again when viewing your post on Netscape - FLY 1 (Dallaz) 14:06:38 02/04/02 Eric, can you read this? --> - my91z 14:18:35 02/04/02 now with my old Netscape, yes! and..... - FLY 1 (Dallaz) 14:37:10 02/04/02 ouch. That hurts. see inside >>> - my91z 15:25:06 02/04/02 hey! - FLY 1 (Dallaz) 01:40:43 02/05/02 yeah, I knew you were messin' :-) I dunno what's up w/> - my91z 07:31:34 02/05/02 <<< SEARCH is your friend! - FLY 1 (Dallaz) 13:22:55 02/05/02 that picture is getting around..... :) (n/m) - felixx23 12:52:42 02/05/02 Never time to do it right, always time to do it twice. ;) (n/m) - SactoTodd 13:26:50 02/04/02 Hey, I like that one. You made my sig> - JRH(KY) 13:48:56 02/04/02 well, not to take anything away, but i believe it is an old - Jefe 13:59:59 02/04/02 I figured as much so I'll remove Todd's name unless - JRH(KY) 14:03:30 02/04/02 Uh, yeah, I just thought of it. ;) - SactoTodd 14:15:06 02/04/02 kinda funny but i also have a friend dustin with a 90Z>> - MBS103 13:36:48 02/04/02 Its the Same dustin.. cause that is where it all started - Irocsx2002 13:43:24 02/04/02 i dont think its the same dustin, AshZ friend dustin is in>> - MBS103 20:59:04 02/04/02 Thats funny, I just met him and saw his car yesterday - BDz32 (FL) 13:50:31 02/04/02 2 things every rebuilder should know - YellowZXTT 13:51:22 02/04/02 Rod bearings are fine. Te crank main bearings are wrong. (n/m) - AshsZ (LUMBRJCK) 13:55:03 02/04/02 i am NOT impressed with nissan parts people or mechanics> - wickdGSXR 16:40:18 02/04/02 That's why I had my short block professionaly done - MikeH(Twin GT35BB Incon Z) 18:04:49 02/04/02 don't go cheap, pay now or pay much more later (n/m) - MikeH(Twin GT35BB Incon Z) 18:10:30 02/04/02
Post a Followup	You cannot reply to this message because you are not logged in.