Subject	Don't ever sweat ASH, while his heart is good, his math isnt
Posted by	ni[x]it on January 05, 2002 at 11:34 AM
	This message has been viewed 196 times.
In Reply To	The exaust gas will mix in the center of the X posted by Specialty-Z on January 05, 2002 at 11:26 AM
Message	: the pipe comes to a knife edge inside and if you look down each tube you can see the full opening of each pipe. Half of exaust from each tube will split down each of the exit tubes. This design should cause a better scavenging effect. : The exaust cannot cross each other inside to exit the opposite side tube because the velosity is too great. : Take a look at the stillen or B&B X pipe the exaust is really staying mostly on the side it came from and mixing slightly in the middle. Also if you do the math A single 3" pipe flows more then two 2 1/4" pipes. two 2 1/2" pipes flow around the same as one 3 1/2" pipe. I forget the formula But I remember doing the math for every differant configuration possible. I will try to get a picture up soon of what the inside looks like. you make an excellent product...there is no question. you're pipes look excellent. i just want you guys to know that there was lots of traffic and it was very dangerous. It was also a little bit wet outside, as I believe it was starting to snow. - down5hift 13:17:28 12/31/01 (931) aim: nixit911
Follow Ups	Pictures of Specialty-Z's (Greg Dupree) custom X-pipes - Playboy 01:26:08 01/05/02 how much? (n/m) - MisterZ(OKC) 01:29:48 01/05/02 <<<<<<<look in classifieds (n/m) - snoguitar 01:30:32 01/05/02 as usual... very nice and functional =) (n/m) - NIZZAN 02:38:21 01/05/02 H-pipe is better than X-pipe! >>> - FLY 1 (Dallaz) 04:01:04 01/05/02 My take on this (just theory) - Turbodog (CT) 07:29:02 01/05/02 AND in fact, you would want the "X" cross section to be same - AshsZ (G'Ville Fab Whore!) 09:30:43 01/05/02 You need to see pics of the inside (n/m) - StEaMyZ(ZtoyZ.NET©) 12:58:34 01/05/02 dyno test rpove h pipes(x pipes) rob hp>>>> - willflow 21:16:31 01/05/02 H-Pipe theory. The higher the velocity of the exhaust>> - not-hrz 11:36:02 01/05/02 Check out this link - F8IZHIS 15:02:18 01/05/02 The "X" angles aren't right. >>> - AshsZ (G'Ville Fab Whore!) 09:26:33 01/05/02 The exaust gas will mix in the center of the X - Specialty-Z 11:26:13 01/05/02 Don't ever sweat ASH, while his heart is good, his math isnt - ni[x]it 11:34:30 01/05/02 If I didn't already have a X-pipe, I would buy Greg's - not-hrz 11:42:32 01/05/02 Thanks Tony! I had never seen the B&B 2 1/2" .... - Specialty-Z 12:01:22 01/05/02 This is a first prototype X pipe for the Z32........ - Specialty-Z 12:25:20 01/05/02 also turbo motor's tend to have less exaust pulse..... - Specialty-Z 12:56:45 01/05/02 What about just straight pipe out to eliminate the X or H? (n/m) - ZilverTT 00:41:33 01/06/02 Re: What about just straight pipe out to eliminate the X or - Specialty-Z 01:41:05 01/06/02 Here is the Stillen X-pipe - socos 14:17:10 01/05/02
Post a Followup	You cannot reply to this message because you are not logged in.