Subject	My DYNO results! pics and stuff! 448 RWHP & 531 torque
Posted by	NIZZAN on July 31, 2001 at 4:25 PM
	This message has been viewed 70 times.
Message	well... After a freaking disappointing weekend at the race track, I feel much better today. My Z is officially a "DYNO QUEEN"! my 1st run yielded 448 rear wheel horsepower and 518 pounds of rear wheel torque. with a 15 % drivetrain loss, that converts to 527 horsepower and 609 pounds of torque at the motor. can you believe this is with STOCK turbos at 17 psi and a 60 shot of Nitrous??? check out how the dyno curve just keeps going up for horsepower! The torque stayed pretty flat and gradually dropped off. needless to say, I was very pleasantly surprised. My 2nd run made less horsepower because it was heat soaked. BUT... It made A LOT more torque! This 2nd run shows 445 rear wheel horsepower and 530 pounds of torque! Unfortunately, the power drops off pretty fast. I had problems adjusting my HKS EVC and boost started dropping off after 5000 RPM. I only ran 14 psi after that point. feel the wrath of NIZZAN.... LOL my dyno queen. I cant wait to get her back out to a good racetrack! thanks to everyone that supported me! Alfred Rhee (Fullerton, California) 95 300ZX TT Stage IV+ 93 A'PEXi RX7 TT (sold) 91 MR2 turbo (daily driver) Click here to visit my website
Follow Ups	My DYNO results! pics and stuff! 448 RWHP & 531 torque - NIZZAN 16:25:45 07/31/01 crazyness - Jack B. 16:28:49 07/31/01 I didn't know you actually could spray NOS to the FMIC - U ZCREAM (Jax,FL) 16:33:11 07/31/01 its possible i was going to "purge" my nos in the IC's.. - TAGURIT(NJ) 17:01:25 07/31/01 Make it run and that will be a neat trick>> - Zster 17:55:13 07/31/01 very nice dude!!!! congrats!!!! (n/m) - TAGURIT(NJ) 16:30:12 07/31/01 Excellent! Minus the NOS that's about where I hope to be - Patrick [Buffalo] 16:30:21 07/31/01 Not bad for 100k+ mile motor :-). Awesome. (n/m) - ZHOUND 16:36:15 07/31/01 hehehe....I know that one - StEaMyZ(ZtoyZ.NET©) 16:39:09 07/31/01 Will do. (n/m) - ZHOUND 17:10:57 07/31/01 115,500 miles to be exact =) (n/m) - NIZZAN 16:44:53 07/31/01 WOW....very nice....those are awesome numbers - StEaMyZ(ZtoyZ.NET©) 16:37:45 07/31/01 thanks... yeah I think I may have a boost leak - NIZZAN 16:44:16 07/31/01 Did you reset your EVC after you installed your NOS? - Spongerider 16:38:36 07/31/01 yeah, i've been trying like crazy to get it dialed in - NIZZAN 16:50:19 07/31/01 nice, congrats. (n/m) - spotz 16:39:34 07/31/01 Congrats! What size injectors are you using? (n/m) - Z-Jay (Canada) 16:45:38 07/31/01 stock. the extra fuel comes from the NOS fogger nozzles. (n/m) - NIZZAN 16:56:02 07/31/01 As well as the cooling effect from the NOS too. (n/m) - Spongerider 17:16:15 07/31/01 nice!! :) (n/m) - Playboy 16:49:53 07/31/01 A stupid question inside >> - timz 16:58:30 07/31/01 scales aren't equal. (n/m) - SactoTodd 17:15:02 07/31/01 Nope! All the dyno sheets I've seen, hp=torque at 5252 rpm>> - timz 17:48:43 07/31/01 x axis is same=rpm, there are 2 y-axis for torque - Chip 18:13:12 07/31/01 yup... left side is the horsepower, right side is the torque (n/m) - NIZZAN 18:18:40 07/31/01 I got it!Thanks! Which car is faster now? The 7 or the Z? (n/m) - timz 18:46:21 07/31/01 wow, makes me wonder what i'll dyno next weekend w/ my setup - Wagz(luv me some SteamyZ) 17:14:37 07/31/01 nice numbers! congrats! - Bernie 17:25:11 07/31/01 I'd like to see those too...NOS on top of boost scares me (n/m) - wesman [92TT-less ] 18:06:12 07/31/01 Screw all you guys getting NOS after I get mine! ;) - SeedyRom 17:31:29 07/31/01 Wow..very nice.... (n/m) - Pats300zx 17:32:11 07/31/01 Wow!! Great results with your mods. You have as much torque - TwinTurboPete 17:40:58 07/31/01 Hey ttpete I have a question for you. - ZHOUND 17:57:18 07/31/01 On the street, I run 1.5 bar of boost but its colder up here - TwinTurboPete 22:57:13 07/31/01 Damn, when Fontana opens..... - KILLR300ZX 18:04:04 07/31/01 Nice!!!! - Matrix-Z's 18:26:16 07/31/01 one more nice pic of my wheels spinning the dyno rollers - NIZZAN 18:27:12 07/31/01 woah!!!! (n/m) - SamBoost 04:52:24 08/01/01
Post a Followup	You cannot reply to this message because you are not logged in.