Subject	make sure the TPS shaft is machined correctly
Posted by	vorpalZed on November 02, 2020 at 11:21 AM
	This message has been viewed 429 times.
In Reply To	PSA: RobZ Billet Aluminum 62mm Upgraded Throttle Body Set posted by MJzTTZ on November 02, 2020 at 10:05 AM
Message	Every previous set of RobZ throttle bodies I've worked on (I have a set as well) has had a poor fit to the TPS causing TPS voltage readings to wander... quite a lot. We've had to build up the shaft so there was a tight fit for the TPS typically by wrapping with Teflon tape.
Follow Ups	PSA: RobZ Billet Aluminum 62mm Upgraded Throttle Body Set - MJzTTZ 10:05:24 11/02/20 Which FB group? (n/m) - ConVerTT 10:08:25 11/02/20 Re: Which FB group? - MJzTTZ 10:15:25 11/02/20 Re: Which FB group? - MJzTTZ 10:22:05 11/02/20 Re: PSA: RobZ Billet Aluminum 62mm Upgraded Throttle Body Set - MJzTTZ 10:24:53 11/02/20 make sure the TPS shaft is machined correctly - vorpalZed 11:21:57 11/02/20 ^ This! (n/m) - MixManMash 12:25:11 11/02/20 Re: make sure the TPS shaft is machined correctly - OleMissFan 13:51:45 11/02/20 I have this issue as well, drivability has been poor - komplexZTT 15:39:32 11/02/20 Mine do not have this issue. Different run maybe? (n/m) - ConVerTT 17:45:10 11/02/20 I fixed the problem with the shaft - AndrewG 06:34:06 11/03/20 Excellent! (n/m) - ConVerTT 08:43:48 11/03/20 I removed my tape and did this instead - komplexZTT 10:19:06 11/04/20 Same here re the TPS and spacing washers (n/m) - AndrewG 11:31:10 11/04/20 Could the TPS voltage readings cause the engine to die? - KevinsFairlady 11:05:52 11/03/20 Whats the consensus on these are they worth? - JerseyTex 12:49:46 11/02/20 Re: PSA: RobZ Billet Aluminum 62mm Upgraded Throttle Body Set - MJzTTZ 15:13:10 11/02/20 I already sent him an email (n/m) - Dallas DamonZ 16:06:49 11/02/20 Would be nice if someone could post a before/after dyno... - Stanky (BC) 17:47:56 11/02/20 I doubt you'll see any difference on a dyno. (n/m) - MixManMash 21:46:05 11/02/20 I've been running mine since ~2012 IIRC -I'm happy with them - BoneZ (MD) 19:54:58 11/02/20 Re: I've been running mine since ~2012 IIRC -I'm happy with them - MJzTTZ 20:02:02 11/02/20 I didn't do a comparison- built the car altogether - BoneZ (MD) 18:09:39 11/03/20 Re: PSA: RobZ Billet Aluminum 62mm Upgraded Throttle Body Set - DanielThomas 00:24:39 11/04/20 What does it take to replace those seals? - ZXoltan 07:10:36 11/04/20 It's been a while, but if I recall correctly - BoneZ (MD) 20:03:40 11/04/20 Is there a link to the group buy anywhere? I cant find it - Mr.Stacy 10:57:21 11/06/20 Re: Is there a link to the group buy anywhere? I cant find it - Zeus 18:21:55 11/06/20 Thanks (n/m) - Mr.Stacy 16:12:01 11/07/20
Post a Followup	You cannot reply to this message because you are not logged in.