Subject	Like most mods on a car, it depends on your goals
Posted by	BlackholeZ on August 05, 2020 at 10:39 AM
	This message has been viewed 306 times.
In Reply To	Rgs vs gktech vs powertrix FUCA posted by ltownsgrimreaper on August 04, 2020 at 05:17 PM
Message	Most of the adjustable FUCAs require a solid tension rod. This makes turn in amazingly sharp and direct, but also makes any bumps in the road feel like you just fell off a cliff. Solid tension rods very much compromise the comfort of the car for handling. If you're wanting to lower the car a bit and correct the camber, the 300degree kit will accomplish that while allowing you to keep stock bushings in the tension rod and keep the car comfortable for daily driving. -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Rgs vs gktech vs powertrix FUCA - ltownsgrimreaper 17:17:28 08/04/20 I have Powertrix FUCA's - Drk93TT 17:50:48 08/04/20 300degree camber kit. - slayer fan 18:13:53 08/04/20 For a mild drop, I'll 2nd the 300D shim kit or a self fab'd - black300zx 19:59:40 08/04/20 300D shim kit here. Don't bother w/ others. (n/m) - Gordo LSZ Daytona 21:36:28 08/04/20 Yep, went with 300 degree when I bought Bernie's OEM - 300MPH 21:50:30 08/04/20 Yep. Me too. (n/m) - Bernie (NoVA) 01:13:33 08/05/20 Me three. (n/m) - Ghoztt (MD) 18:43:12 08/05/20 Me four. Replaced a bent set of adjustable FUCA's. (n/m) - Mike (NoVA) 09:32:02 08/06/20 Re: Yep, went with 300 degree when I bought Bernie's OEM - DanielThomas 11:52:01 08/07/20 I can include my install guide w. them. It's very streamline (n/m) - Bernie (NoVA) 12:03:01 08/07/20 Made shims to fine tune camber - 1/8" and 1/4" AL bar stock - Gordo LSZ Daytona 12:01:21 08/07/20 Safer to have holes vs slots & not risk slipping out (n/m) - Bernie (NoVA) 12:15:39 08/07/20 I was planning on having a set of varied widths myself. - Ghoztt (MD) 12:34:09 08/07/20 Re: Rgs vs gktech vs powertrix FUCA - Rob260 07:09:42 08/05/20 Like most mods on a car, it depends on your goals - BlackholeZ 10:39:06 08/05/20 Re: Like most mods on a car, it depends on your goals - ltownsgrimreaper 15:11:45 08/05/20 Re: Re: Like most mods on a car, it depends on your goals - ouikikazz 19:58:24 08/05/20 As long as you've got solid bushings in the tension rods - BlackholeZ 10:12:03 08/06/20 Get the Nismo FUCAs + 300° camber kit from Bernie (n/m) - Aqualung 15:52:20 08/05/20 Wasn't there about 10K miles on your failed PT FUCA's? - Mike (NoVA) 09:34:31 08/06/20 Sounds about right. Couldn't have been much more than 10-15k (n/m) - Aqualung 23:15:54 08/08/20 AMS for life! (n/m) - ForceFedTT 19:02:56 08/06/20 I've got a pair of AMS FUCA's that I refuse to sell - Gordo LSZ Daytona 19:28:08 08/06/20 There are scrap metal bins for your future. (n/m) - Bernie (NoVA) 10:07:27 08/07/20 been there... done that - vorpalZed 10:46:22 08/07/20 Lol - Love it!!! (n/m) - RICH1 11:04:25 08/07/20 Yup. (n/m) - Bernie (NoVA) 12:03:45 08/07/20 So much winning right there. (n/m) - MixManMash 15:30:32 08/07/20 I have 2 pairs of Noltec for the same reason - BigA 12:54:22 08/07/20 Put in scrap bin. No reason to clutter your garage. (n/m) - Bernie (NoVA) 15:38:07 08/07/20
Post a Followup	You cannot reply to this message because you are not logged in.